Trane Axiom GEH-E035, Инструкция по установке, эксплуатации и обслуживанию

Страница: 56 / 124

56 WSHP-SVX01Y-EN
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
1. Remove service access panel at the unit front.
2. Find the blower motor relay. The relay location is
consistent in all control configurations.
Figure 60. Relay location (GEH)
Removing Speed-tap Wire
1. For units w/o Hot Gas Reheat: Remove undesired
speed-tap wire from 1K4 relay at spade 3. Wire tie
the lead, to eliminate a short.
2. For units with Hot Gas Reheat: Remove undesired
speed-tap wire from 1K8 relay at spade 6. Wire tie
the lead, to eliminate a short. Hot Gas Reheat
requires both speed taps to be adjusted to enable
reheat as the lower speed tap.
Connecting Desired Speed-tap Wire
1. For units without hot gas reheat, select desired
speed-tap wire. Connect desired speed tap wire to
1K4 relay at spade 3.
2. For units with hot gas reheat, select desired speed-
tap wire. Connect desired speed tap wire to 1K8
relay at spade 6.
3. Install service front panel. Reconnect power to the
unit.
Table 42. .4-speed motor (115, 208, 230, 265)
Lead Colors
Lead Black Blue
Orange
Red
Speed High
Medium
High
Medium
Low
Low
Table 43. 3-speed motor (380, 415, 460)
Lead Colors
Lead Black Blue
Orange
Speed High
Medium Low
N No otte e:: When using the medium or low speed tap, the
purple wire must be jumpered to the high speed
tap (blk).
Table 44. 2–speed motor (575)
Lead Colors
Lead Black Blue
Speed High
Low
Hole Plug Installation
1. Locate two Hayco plastic plugs enclosed with the
Installation, Operation and Maintenance manual.
2. Use these plugs to plug the two shipping bolt holes
in the bottom of the units after shipping bolt
removal.
Airflow Adjustment
W WA AR RN NIIN NG G
R Ro otta attiin ng g C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n rro otta attiin ng g cco om mp po on ne en nttss ccu uttttiin ng g a an nd d sslla assh hiin ng g
tte ecch hn niicciia an n w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss
iin njju urry y..
D Du urriin ng g iin nsstta alllla attiio on n,, tte essttiin ng g,, sse errv viicciin ng g a an nd d
ttrro ou ub blle essh ho oo ottiin ng g o off tth hiiss p prro od du ucctt iitt m ma ay y b be e
n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e a an nd d e ex xp po osse ed d rro otta attiin ng g
cco om mp po on ne en nttss.. H Ha av ve e a a q qu ua alliiffiie ed d o orr lliicce en nsse ed d sse errv viicce e
iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n p prro op pe errlly y ttrra aiin ne ed d iin n
h ha an nd dlliin ng g e ex xp po osse ed d rro otta attiin ng g cco om mp po on ne en nttss,, p pe errffo orrm m
tth he esse e tta asskkss..
N No otte e:: GEH/V 6 to 25 ton units only.
To increase cfm, loosen the turns open set screw on
the sheave, and turn the sheave clockwise. To decrease
cfm, Loosen the turns open set screw on the sheave,
and turn the sheave counterclockwise.
To increase belt tension, loosen the adjustment bolt
and pull motor mounting plate back until the belt is
tight. Tighten the adjustment bolt after the belt has
reached the desired tension.
See the figure below for fan motor and sheave
adjustment.
IIn nsstta alllla attiio on n