Trane Axiom GEH-E035, Инструкция по установке, эксплуатации и обслуживанию

Страница: 44 / 124

44 WSHP-SVX01Y-EN
Installation
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
General Installation Checks
The checklist below is a summary of the steps required
to successfully install a commercial unit. This checklist
is intended to acquaint the installing personnel with
what is required in the installation process. It does not
replace the detailed instructions that are in the
applicable sections of this manual.
1. Remove packaging and inspect the unit. Check the
unit for shipping damage and material shortage; file
a freight claim and notify appropriate sales
representation.
The GEHE 0.5 to 5 ton units have been anchored to
the skid by (2) shipping bolts. The removal of these
bolts will require a 3/8 (9.7 mm) ratchet with a 0.5
(12.7 mm) socket.
The GEVG 0.5 to 5 ton and GEVE 6 to 25 ton units
have been anchored to the skid with (4) angle
brackets. Remove these brackets before lifting unit
into place.
The GEH 6 to 15 ton units are anchored to the cross
brace of the skid with (4) wood screws. Remove
these screws prior to lifting the unit into place.
2. Verify the correct model, options and voltage from
the unit nameplate.
3. Pull out all field attached parts (i.e. filter rack, duct
collar, filter and mounting screws) from the unit
packaging for field mounting.
4. Verify the installation location of the unit will
provide the required clearance for proper
operation.
5. Remove refrigeration access panel and inspect the
unit. Be certain the refrigerant tubing has clearance
from adjacent parts.
6. Fabricate and install duct work
7. Install and connect a condensate drain line and trap
to the drain connection.
Main Electrical
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y tth ha att n no o
p po ow we err iiss p prre esse en ntt w wiitth h a a v vo ollttm me ette err..
1. Verify the power supply complies with the unit
nameplate specifications.
2. Inspect all control panel components; tighten any
loose connections.
3. Connect properly sized and protected power supply
wiring to a field-supplied/installed disconnect
switch and to the main compressor contactor/
power block 1K1 (compressor contactor on the 0.5
to 5 ton) for GEH/V 0.5 to 5 tonor 1TB1 for GEH/V 6
to 25 ton equipment in the unit control panel .
4. Install proper grounding wires to an earth ground. .
N No otte e:: All field-installed wiring must comply with NEC
and applicable local codes.
Electric Heat Requirements
1. Verify that the power supply complies with the
electric heater specifications on the unit and heater
nameplate.
2. Inspect the heater junction box and control panel;
tighten any loose connections.
3. Check electric heat circuits for continuity.
Low Voltage Wiring (AC)
Requirements
1. Install the zone sensor or thermostat.
2. Connect properly sized control wiring to the proper
termination points between the zone thermostat or
sensor and the unit control panel.
Filter Installation
Each unit ships with 1 (25.4 mm) standard, 2 (50.8 mm)
standard, 2 in. MERV 8 or 2 in. MERV 13 filter. The
quantity of filters is determined by unit size. The GEH
0.5 to 5 ton units require field installation of the 1" or 2"
filters rack. All sheet metal bracket, filter and hardware
are in a box located on the side of the unit within the
unit packaging. All vertical and GEH 6 to 15 ton
horizontal units ship with the filter rack and filters
factory installed.