background image

2

ST1-075A Ia 12/98

IMPORTANT!

Before you operate this attachment, read this
manual completely and carefully so you will
understand the safety instructions and the
operation of the controls and safety equipment.
You must comply with all DANGER, WARNING
and CAUTION notices.  They are for your benefit.

All references to the right side, left side, front, or
rear are given from the operator’s seat of the host
vehicle looking in a forward direction.

TRAK International, Inc. is herein after referred to
as TRAK.

IMPORTANT

!

A Warranty Registration Form must be filled out by
the TRAK distributor, signed by the purchaser, and
returned to TRAK once the product is sold and/or
put into service.  This report activates the warranty
period, assuring that your claims during the
warranty period will be honoured and processed
expediently. To guarantee your full warranty
service, make sure your distributor has returned
the business reply card of this form to TRAK.

TRAK reserves the right to make changes on and
to add improvements upon it’s products at any time
without public notice or obligation.  TRAK also
reserves the right to discontinue manufacturing
any product at its discretion at any time.

For your easy reference when ordering
replacement parts or making service inquiries on
this attachment, record its model and serial
numbers on the back cover of the manual.  The
numbers are stamped on the serial number plate
located on the left  side of the motor housing
(Figure 1).

IMPORTANT!

The replacement of any part on this product by
anything other than a TRAK
authorized replacement part may adversely affect
the performance, durability, or safety of this
product and will void the warranty.  TRAK assumes
no liability for unauthorized replacement parts
which adversely affect the performance, durability
or safety of this product.

f

Figure 1

om

OM0240

  Disclaimer

  Reports

  The Manual

  Replacement Parts

Introduction

Serial # Plate

This Owners/Operators manual provides the
information you need to correctly operate and
maintain this attachment.

Содержание SAND TRAK ST1-075A la

























Отзывы: