TrailMax TD-40-T Скачать руководство пользователя

Страница: 26 / 62

page 26

TD-40-T

FINE GROOVES

ABRASIVE FOREIGN

MATERIAL OR POOR

QUALITY BRAKE LINING

LOOSE RIVETS OR BOLTS

OR FOREIGN MATERIAL

IN RIVET HOLES

MACHINE OR REPLACE

BRAKE DRUM AND

REPLACE LINING

MACHINE OR REPLACE

BRAKE DRUM. USE RIVET

HOLE PLUGS.

REPLACE

MISHANDLING

REPLACE. CLEAN HUB

BEFORE INSTALLATION.

INSTALLATION ON

DIRTY HUB

OUT OF ROUND:

BALANCE

GROOVES ALONG EDGES

OF LINING

ABRASIVE MATERIAL

COLLECTING ALONG

EDGES OF LINING

DUST SHIELD MAY CAUSE

OR CURE THIS. MACHINE

BRAKE DRUM.

REPLACE. SPECIFY

BALANCED DRUM WHEN

ORDERING REPLACEMENT

CRACK BETWEEN PILOT

HOLE AND BOLT HOLE

WHEEL HITTING

BRAKE DRUM

INSTALLATION ON

DIRTY HUB

MOUNTING FLANGE SEPARATED

FROM HOOP SECTION OF DRUM

REPLACE DRUM. CLEAN

THE HUB PRIOR TO

INSTALLING NEW DRUM.

INCORRECT APPLICATION.

REPLACE BRAKE DRUM

WITH CORRECT PART.

HEAT SPOTTED OR HARD

SPOTS IN BRAKE SURFACE

HIGH LOCALIZED

HEATING AND COOLING

CYCLES

GRIND HARD SPOT

AND MACHINE DRUM

BALANCE WEIGHT

FALLEN OFF OR NOT A

BALANCED DRUM

OUT OF ROUND:

CONCENTRICITY

MACHINE OR REPLACE.

CHECK FOR CORRECT FIT
& CLEARANCE TO WHEEL.

IMPROPER FIT TO PILOT

OR IMPROPER SEATING

ON WHEEL OR HUB

EXCESSIVE WEAR

ABRASIVE FOREIGN

MATERIAL OR POOR

QUALITY BRAKE LINING

MACHINE OR REPLACE

OUT OF ROUND: VARIATION

IN DIAMETER

MACHINE OR REPLACE

HEAT DISTORTION

PROBLEM

REMEDY

CAUSE

Brake Drum Troubleshooting Chart (continued)

Maintenance

Содержание TD-40-T































































Результаты поиска

Содержание TD-40-T

Отзывы:

Похожие инструкции для TD-40-T

Бренды по названию

Популярные бренды

TrailMax TD-40-T, Руководство пользователя

Результаты поиска

Содержание TD-40-T

Отзывы:

Похожие инструкции для TD-40-T

Бренды по названию

Популярные бренды