manualshive.com logo in svg

TrailMax TD-40-T, Руководство пользователя

Поделиться
Скачать
TrailMax TD-40-T Скачать руководство пользователя страница 35

page 35

TD-40-T

®

Maintenance

Slack Adjuster Function Test

1. Remove the slack adjuster from the axle.

2. Using a torque wrench that measures in lb-in., rotate the adjusting nut counter-

clockwise 22 turns. This is enough turns of the adjusting nut to rotate the camshaft gear
1 full revolution. If the torque value remains below 25 lb-in. during this test, then the
slack adjuster is functioning normally.

COMPONENT DAMAGE!

In step 2 turn the adjusting nut in the counterclockwise direction ONLY!

If you turn the adjusting nut in the wrong direction while the pawl is en-
gaged, the pawl teeth will be damaged and the slack adjuster will not
automatically adjust the brake clearance. Replace damaged pawls be-
fore returning the vehicle to service.

3. If the torque value exceeds 25 lb-in. while making the 22 turns, then the slack

adjuster is not working correctly and should be rebuilt or replaced.

4. Reinstall the slack adjuster on the axle, and check the free stroke length. Adjust

if necessary.

For more information regarding the slack adjuster, refer to Meritor Maintenance

Manual 4B, 

Automatic Slack Adjuster

.

Brake Lubrication

Every six months or 50,000 miles the brake system should be lubricated with NLGI

Grade 1 or 2 lithium base grease. There are three grease fittings for each wheel; one
on the slack adjuster, one on the inner cam bushing, and one on the outer cam bushing.
Add grease until fresh grease appears at the purge point of the component. Clean up
any excess grease thoroughly so that it will not attract dirt or contaminate the brake
linings.

For more information regarding brake lubrication, refer to Meritor Maintenance

Manual 14, 

Trailer Axles,

 Section 13.

BRAKE LINING CONTAMINATION!

Do not get grease or oil on the brake linings or drums.

M

A

I

N

T

E

N
A
N
C

E

WARNING

!

CAUTION

!

Содержание TD-40-T































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды