TrailMax TD-40-T Скачать руководство пользователя | Manualshive

Страница: 18 / 62

background image

page 18

TD-40-T

®

2.1

Structural Components

Sub-Frame

Other than for periodic or special inspections the trailer sub-frame requires no regular

maintenance other than washing. Keeping the trailer clean will help you notice other
things such as cracked welds or corrosion. If your application requires the hauling of
corrosives then frequent washdowns are very important.

Deck

The tilt deck is the major load-carrying member of the trailer. It requires no regular

maintenance other than a periodic check for broken welds, loose fasteners and corro-
sion. If the trailer has been overloaded or in an accident, inspect the tilt deck carefully.

It may be necessary to apply a new coat of wood preservative after decking has

aged and become dry. The best time to apply preservative is during warm weather for
better penetration. Replace decking when necessary. Occasionally check for loose,
missing, or broken deck screws.

2.2

Sub-Assembly Components

Drawbar Eye

Check the eye for cracks, loose fasteners and wear. Regularly apply a coating of

grease to the eye to prevent accelerated wear.

The fasteners for the drawbar eye are very important and deserve careful attention.

Replace the bolts if they are damaged in any way, and replace the locknuts if worn.
Torque the fasteners to 315 to 420 lbs.-ft.

Maintenance

«
...
16
17
18
19
20
...
»

Содержание TD-40-T































































Отзывы:

Нет отзывов

Похожие инструкции для TD-40-T

Бренд: Polaris Страницы: 665

Бренд: citEcar Страницы: 28

RANGER Diesel 2013

Бренд: Polaris Страницы: 97

Бренд: Polaris Страницы: 141

Бренд: Polaris Страницы: 476

Бренд: E-Z-GO Страницы: 66

Бренд: Labrie Страницы: 145

Бренд: Taxa Outdoors Страницы: 5

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 114

Workman 133-3016

Бренд: Toro Страницы: 8

Бренд: FIORENTINI Страницы: 21

Trail-Blazer TB-6000

Бренд: J&M Страницы: 30

Бренд: Motoalliance Страницы: 3

Impact Trailer 100

Бренд: Motoalliance Страницы: 7

Бренд: Ingersoll-Rand Страницы: 40

Бренд: Honda Страницы: 62

Бренд: Honda Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды