TrailMax TD-40-T Скачать руководство пользователя

Страница: 7 / 62

page 7

TD-40-T

Operation

P
E

R
A

1.5

Alert Symbols

It is important that you know the meaning of the following symbols that are used

throughout this document.

SAFETY ALERT!

This is the safety alert symbol. It is used to alert you to potential per-

sonal injury hazards. Obey all safety messages that follow this symbol to
avoid possible injury or death.

DANGER!

DANGER! indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING!

WARNING indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION!

CAUTION indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

CAUTION

CAUTION used without the safety alert symbol indicates a potentially

hazardous situation which, if not avoided, may result in property dam-
age.

DANGER

WARNING

CAUTION

Содержание TD-40-T































































Результаты поиска

Содержание TD-40-T

Отзывы:

Похожие инструкции для TD-40-T

Бренды по названию

Популярные бренды

TrailMax TD-40-T, Руководство пользователя

Результаты поиска

Содержание TD-40-T

Отзывы:

Похожие инструкции для TD-40-T

Бренды по названию

Популярные бренды