background image

Operator’s manual for Pentruder 8-20HF/iQ and Pentpak HF-power pack  – Original instructions

 

Page 37

 

Oil change in the travel  
and arm feed worm gear  
transmission:  

This oil should be changed every 80 hours of operation when service is 
done to the machine. The travel worm gear transmission is filled with 60 
ml and the arm feed worm gear transmission with 80-100 ml (0.085 – 
0.106 quart) of Omega 680 oil.  

 

Oil change in slip clutch 
transmission housing:  

Fill with 25 ml (0.026 quart) of Omega 690 oil every 80 hours of operation. 

 

 
Oil change in the  
HF-motor high speed  
transmission: 

This oil change may only be carried out by a trained technician familiar 
with this machine.

Change oil every 80 hours of operation.  

 

Important! Before attempting to change oil, clean thoroughly around the plug and blow with 
compressed air before the plug is removed. If dirt is allowed to enter the gearbox, the 
gearbox may seize and any warranty is void.  

 

Unscrew the oil-plug and drain the gearbox completely. Refill with 0.235 L 
(0.248 quart) of 

clean and preferably filtered 

gearbox oil, preferably 

Mobil SHC 626. It must be synthetic oil with 75W viscosity. The oil must 
meet GL5 specifications. Clean the magnetic plug, fit it and tighten again. 

 

Cooling housing at rear  
of HF-motor: 

Fill with 85 ml of Mobil SHC 626 at service (every 80 hours of operation). 

 
 
Overload clutch: 

If any of the overload clutches have been overloaded or worn out, a 
trained mechanic can repair the coupling by replacing the clutch plates, 
The coupling is easy to replace, and must not necessarily be brought to 
your dealer for service.  

 

Digital communication 
connectors: 

Check all connectors for proper function and replace when necessary.  

 

 

All parts in the connectors are available (except remote control 
connector). All wires can be re-installed with standard hand tools (except 
remote control connector).  

 
Quick disconnect coup- 
ling for the saw blade: 

The flange and the spindle are provided with drive dogs to transmit the 
torque to the blade and centering cone to align the flange to the spindle. 
Clean the dogs and the cone regularly to allow the flange to always be 
aligned and properly in mesh. 
 
The centering cones in the spindle and flanges should be brushed with a 
brass brush on the outside and inside and be kept perfectly clean at all 
times. If they are not clean, the coupling may be damaged beyond repair 
and the blade may not run true.   

 

Remote Control unit: 

Check the remote control unit for correct function and that the connector 
is clean and undamaged. 

 

Содержание Pentpak HF-power pack













































Отзывы: