Tractel altotir 200, Руководство по эксплуатации и обслуживанию

Страница: 49 / 140

49
GB
members (Fig. 8, item 7) are in contact
with the frame’s anchoring tube (Fig. 11,
item 2).
• Check that the altotir™ winch cannot
pivot around the frame anchoring tube.
Phase 2: Installing the wire rope in pulleys
• Using the control unit, unwind the wire
rope, keeping it tensioned while
unwinding. Insert the wire rope in the
idler pulley, winch side (Fig. 11, item 4).
Using the control unit, unwind the wire
rope again, keeping the wire rope
tensioned. Insert the wire rope in the idler
pulley, load side (Fig. 11, item 5).
NOTE: Tractel ® recommendation:
Two persons required when installing wire
rope on pulleys.
• Allow the lifting hook and the limit stop to
hang (Fig. 1, items 2 and 10).
• Lower the assembly formed by the lifting
hook and limit stop (Fig. 1, items 2
and 10) by acting on the control unit.
• At the end of the wire rope travel, check
that two coils of wire rope remain on the
winch warping drum.
Phase 3: Installing the adjustable limit stop
IMPORTANT: The adjustable limit
stop must be installed on the section of lifting
wire rope located between the altotir™ winch
and the idler pulley, winch side (Fig. 11,
item 4).
• Install the adjustable limit stop as detailed
in the procedure given in section. 14.3
• Position the adjustable limit stop to ensure
that:
• When the lifting hook is at the low limit,
the adjustable limit stop (Fig. 11, item 6)
does not interfere with the idler pulley,
winch side (Fig. 11, item 4).
• When the adjustable limit stop is in
contact with the limit stop lever (Fig. 11,
item 9), the limit stop (Fig. 11, item 10)
does not interfere with the idler pulley, load
side (Fig. 11, item 5).
• Manually check that the adjustable limit
stop is locked on the wire rope.
7.3.3 Checks after installation
7.3.3.1 Checks without load
Check that:
• There is no interference between the
adjustable limit stop (Fig. 11, item 6) and
the idler pulley, winch side (Fig.11, item 4)
when the lifting hook is at the low limit.
• There is no interference between the limit
stop (Fig. 11, item 10) and the idler pulley,
load side (Fig. 11, item 5) when the limit
stop lever (Fig. 11, item 9) is actuated by
the adjustable limit stop (Fig. 11, item 6).
• No interference is observed between the
wire rope, equipped with its hook and
limit stop, and the environment along the
entire load lifting height.
• No interference is observed between
the wire rope equipped with its adjustable
limit stop, and the environ ment along the
entire load lifting height.
• The winch stops, on an up-movement
cycle, when the adjustable limit stop
(Fig. 11, item 6) comes into contact with
the limit stop lever (Fig. 11, item 9).
If this is not the case, immediately stop the
up-movement and have the limit stop lever
checked by a qualified technician.
• There are at least two coils of wire rope
remaining in the warping drum at the low
unwinding limit.
• No slack wire rope is observed while the
lifting hook is being lowered, in particular
between the 2 idler pulleys. If any slack
wire rope is observed, fit a weight on the
lifting hook to ensure that the wire rope
remains tensioned (2 kg max.).
7.3.3.2 Checks with load
• Fasten the maximum working load to the
lifting hook (Fig. 1, item 2).
• When the load lifts off the ground, check
that:
- There are no signs of deformation, cracks
or rupture on the anchoring tube (Fig. 11,
item 2) or in the immediate environment.
If any problem is observed, immediately