B
BRAKES
Read all of SAFETY and this section before attempting any procedure. Pay particular attention to Notices, Cautions, Warnings and Dangers.
45
Repair and Service Manual
699322
Figure 28 Catch Bracket and Latch Arm
Parking Brake Pedal Removal and Installa-
tion
Note the location and orientation of the two torsion
springs (8). Remove the push nut (9) and pin (10) (Figure
27) and remove the parking brake pedal. Some models
may use two push nuts on the pin.
To prevent serious injury or death
resulting from the use of worn park-
ing brake components, to not
attempt to re-new worn components. The parking
brake arm latch is a hardened part. Do not grind or
file it as doing so will cause the part to lose its hard-
ness characteristics. A new part must be used.
Installation is in the reverse order of disassembly. Use a
new push nut (or push nuts).
If required, adjust the kick-off cam (3). See the
Pedal Bumper Adjustment
Loosen bumper lock nut and adjust the bumper by rotat-
ing it (Figure 29). The brake pedal must contact the pedal
bumper when pedal is released and the dimension from
the top of the pedal arm to the setscrew heads in the kick-
off cam should be approximately 1/4" - 3/8” (6 - 9.5 mm).
Tighten the lock nut to 12 - 14 ft. lbs. (16 - 19 Nm).
Figure 29 Pedal Bumper Adjustment
Parking Brake Release Linkage Removal
and Replacement
Remove the cotter pin (2), washers (3) and bushings (4)
from linkage rod (1). Remove the linkage rod (Figure 30).
Inspect the bushings (4). If they are worn replace them
with new ones.
Installation is in the reverse order of disassembly.
If required, adjust the kick-off cam (6). See the
Figure 30 Park Brake Linkage and Kick-Off Cam
Parking Brake Kick-Off Cam Removal
1.
Disconnect the parking brake release linkage as
described above.
2.
Loosen the two setscrews (5) from the cam (6) and
remove the cam pivot (7), cam and spacer (8) (Fig-
3.
Inspect the bushings (9,10) and spacer. If they are
worn, replace them with new ones.
4.
Installation is in the reverse order of disassembly.
5.
With the parking brake engaged and fully latched,
there must be no gap between the top of the cam
and the latch arm.
6.
To adjust the kick-off cam (6), engage the parking
brake and loosen the two cam setscrews (5) and
rotate the cam until it contacts the latch arm.
7.
Tighten the setscrews to 45 - 55 in. lbs. (5 - 6 Nm)
torque. Always use new epoxy patch setscrews
when replacing the kick-off cam.
Cam Must Be Against
Latch Arm At This Point
0.0" Gap
(0.0 mm)
Pedal Latch Arm
.03" (.76 mm) Max Gap
After Adjustment Of Cam
1/4" (6 mm) Max Gap At This Point
Catch Bracket
1
4
3
2
Pedal Bumper
Lock
Nut
1/4" - 3/8" (6 - 9.5 mm) Diameter
Drill or Bolt Must Pass
Through Gap
Accelerator
Pedal
7
2
2
4
1
6
8
10
9
5
3
4
3
Содержание LS2 2020
Страница 1: ...REPAIR AND SERVICE MANUAL 699322 A Issued May 2019 653635 B...
Страница 16: ...B xiv Repair and Service Manual TABLE OF CONTENTS 655827...
Страница 17: ...B TABLE OF CONTENTS xv Repair and Service Manual 655827...
Страница 18: ...B xvi Repair and Service Manual TABLE OF CONTENTS 655827...