TOX PRESSOTECHNIK TOX-FinePress PFL 002 Скачать руководство пользователя

Страница: 25 / 72

Transport and storage

TOX_Manual_FinePress_PFS-PFL-PFW_en

5 Transport and storage

5.1

Safety during transport

WARNING

Hazard from suspended loads!

Severe crushing, impacts and serious accidents as a result of improper
transportation and falling load!

Only use lifting gear that is appropriate and in perfect technical condi-
tion, as well as load attachment devices with an adequate safe working
load.

Never stand or work under suspended loads.

Make sure that that no person is in the danger area.

When transporting and setting down, make sure that no parts of the
body become jammed.

Wear suitable personal protective equipment (e.g. safety boots).

CAUTION

Injury from toppling and falling products!

Secure product from toppling, falling, accidentally moving.

Store product horizontally or secure with dowels.

The transportation may only be carried out by authorized personnel.

The product may only be transported with the transport pallet or trans-
port device provided.

The product may only be lifted with suitable lifting devices at suitable
lifting points.
See

Chap. 2.4 Safety symbols, Page 18

Note the weight of the product.
See technical data sheet.

Note the center of gravity of the product.
See general arrangement drawing.

Содержание TOX-FinePress PFL 002









































































Результаты поиска

Содержание TOX-FinePress PFL 002

Отзывы:

Похожие инструкции для TOX-FinePress PFL 002

Бренды по названию

Популярные бренды

TOX PRESSOTECHNIK TOX-FinePress PFL 002, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание TOX-FinePress PFL 002

Отзывы:

Похожие инструкции для TOX-FinePress PFL 002

Бренды по названию

Популярные бренды