Town & Country Fireplaces TC54.CE3 Скачать руководство пользователя | Manualshive

Страница: 1 / 40

background image

SERIAL #

220313-40

TC54.CE3

5056.42562

This appliance may be installed in an aftermarket
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.

This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.

This appliance is suitable for installation in a
bedroom or bed sitting room

TC54.CE3
INSTALLATION
AND OPERATING
INSTRUCTIONS

MODEL

TC54

SERIES C2

MODULAR DIRECT VENT

FIREPLACE

INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.

WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch;
•  Do not use any phone in your building.
•  Immediately call your gas supplier from

a neighbour’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier call

the fire department.

Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.

1
2
3
...
»

Содержание TC54.CE3









































Отзывы:

Нет отзывов

Похожие инструкции для TC54.CE3

Бренд: Pacific energy Страницы: 24

Бренд: Valor Fires Страницы: 49

Бренд: Spartherm Страницы: 28

Бренд: PRITY Страницы: 70

Бренд: Napoleon Страницы: 32

Бренд: Napoleon Страницы: 80

Бренд: NovaFlex Страницы: 24

Cosi square glass set M

Бренд: Gimeg Страницы: 2

Wall Mantel with Base and Trim WD26CP

Бренд: Desa Страницы: 8

Бренд: Outdoor GreatRoom Company Страницы: 12

Comfort Glow CGEFP33PR

Бренд: Desa Страницы: 38

Бренд: Mendip Stoves Страницы: 16

Бренд: Qindao Hichanse Group Страницы: 16

Бренд: Comfort Glow Страницы: 38

Бренд: C&J Страницы: 24

Бренд: Oblica Страницы: 14

Бренд: Empire Comfort Systems Страницы: 6

IronStrike Performer C210AGL

Бренд: IHP Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды