background image

Table of Contents

Caution ...........................................................................................3
Safety .............................................................................................3
Fireplace Dimensions .....................................................................5
Minimum Clearances to Combustible Material ...............................5
Installation Requirements ...............................................................6
Manufactured (Mobile) Home .........................................................6
Window Frame Removal .................................................................6
Locating The Fireplace ...................................................................7
Top Standoffs ..................................................................................7
Framing and Finishing ....................................................................8
Steel Stud Framing Kit .................................................................. 10
Hearth Extension .......................................................................... 12
Maestro Control  ........................................................................... 13
– Plumbing and Electrical ............................................................. 13
Gas Supply ................................................................................... 16
Gas Pressure Check ..................................................................... 16
Horizontal Termination Venting  .................................................... 17
(Power Vented) ............................................................................. 17
Vertical Termination Venting ......................................................... 17
Roof Termination Venting Chart .................................................... 18
Vent Terminal Clearance ...............................................................21
Vent Restrictor Adjustment ...........................................................22
Firebox Panels Installation ............................................................23
Finishing Touch Trim Kit Instructions .............................................24
Lighting Instructions .....................................................................25
First Fire ........................................................................................25
Maestro Control System ...............................................................26
Remote Control Initial Setup .........................................................26
Maestro Control System - Operation ............................................27
Maintenance .................................................................................30
Replacement Parts .......................................................................31
Replacement Parts – Maestro Control System .............................32
Wiring Diagram .............................................................................33
Roof Termination Kit   ...................................................................34
Vent Pipe Dimensions  .................................................................35
Vent Offset Chart ..........................................................................35
Notes ............................................................................................36
Notes ............................................................................................37
Notes ............................................................................................38
Safety Label Location ...................................................................39

2

TC54.CE3 220313-40

Содержание TC54.CE3









































Отзывы: