tousek ST 61 Скачать руководство пользователя страница 25

Страница: 25 / 36

tousek

/ EN_ST-61A_08 / 25. 03. 2020

- 25 -

Electric lock



Electric lock module, page 26

Peripherals



switched off



1–10s adjustable:

The electric lock is activated by push button impulse or impulse from pedestrian button for a

period of time set here to ensure the release depending on the gate situation

Reverse stroke

(only with activated locking!)

Peripherals



switched off



0,5–8s adjustable:

Only with activated lock (electric lock or motorized locking bar): After an impulse is given, a short

closing movement for unlocking (for example, the E-lock) is initiated first, the unlocking is performed and the door is

opening. With an electric lock, the reversal stroke is only carried out in the opening direction. With a motor bolt, depend-

ing on the setting, it is possible to set the reversal stroke also in the closing movement.

Additional module

Peripherals



courtyard/control lamp:

the menu points courtyard lamp and control lamp are ready for adjustment (that means if not

selected, these menu points will not be shown on the display)



status display 1:

with the two potential-free signal contacts K1 and K2, the gate end positions (limits) can be

evaluated.



status display 2:

with the two potential-free signal contacts K1 and K2, the gate end positions (limits), the gate mo-

vement as well as a gate stop outside of the end positions can be evaluated.

Additional module (optional)

•

turn off power supply before installing the additional module!

• Depending on which device, e.g. a

courtyard-/Control lamp

chosen or

evaluation of gate status

should be effected, the corresponding

module

(Z)

has to be plugged to the according slot/plug

(ZM)

of control board.

• Additionally the corresponding value has to be selected in menu point

„Additional module“.

Additional module

Courtyard lamp/

Control lamp

• On the terminals 12/13

a courtyard lamp (H)

can be connected:

230V, max. 100W

• On the terminals 70/71

a control lamp (K) can

be connected:

24Vd.c., max. 2W

12 13 70 71

L N

– +

Additional module

Gate status display

• with potential free signal contacts K1 (Kl.

90/91) and K2 (Kl. 92/93) the gate staturs

can be evaluated in two ways (see menu

point „Additional module“).

• Contact load:

24Va.c./d.c., max. 10W

Function

K1 K2

Gate status display

Gate in CLOSE-Position

Gate in OPEN-Position

Gate in CLOSE-Position

Gate opens or closes

Gate stopped or fault

(Gate not in end position)

Gate in OPEN-position

signal contacts: 0 = open, 1= closed

90 91 92 93

signal contacts

ST 61A

Locking

Peripherals



e-lock/magnetic clamp:

with additional module electric lock/magnetic clamp.



motor lock:

with additional module motorized locking bar.

Motor lock



Motor lock module page, 26

Peripherals



OPEN and CLOSE:

locking via motorized locking bar in both end positions of the gate.



only OPEN:

locking via motorized locking bar only in open position.



only CLOSE:

locking via motorized locking bar only in closed position.

Peripherals

Connections and adjustments

Содержание ST 61





































Результаты поиска

Содержание ST 61

Отзывы:

Похожие инструкции для ST 61

Бренды по названию

Популярные бренды

tousek ST 61, Руководство по подключению и установке

Результаты поиска

Содержание ST 61

Отзывы:

Похожие инструкции для ST 61

Бренды по названию

Популярные бренды