manualshive.com logo in svg

tousek PULL T10, Руководство по монтажу и установке, Страница: 32 / 36

Поделиться
Скачать
tousek PULL T10 Скачать руководство пользователя страница 32

- 32 - 

tousek

  /  EN_PULL-T8-T10-T15-M-S_02  /  25. 03. 2020

9.  Troubleshooting guide

   

M/S

 

Sliding gate operator  PULL T8, -T10, -T15 / Master-Slave

Error

Possible reason

Solution

display: „Stop-button  released“

stop-button not connected or not 

bridged

stop-button (Kl. ) connect or bridge > 

use status display for help

display: „Photocell released“

photocell interrupted

check correct connection hence 

remove obstacle > use status dispaly 

for help   

display: „Main safety sensing edge 

released““

main safety edge interrupted or hot-

wired

check correct connection hence 

remove obstacle > use status dispaly 

for help

display: „Side safety sensing edge 

released“

side safety sensing edge interrupted or 

hot-wired

check correct connection hence 

remove obstacle > use status dispaly 

for help 

display: „AR-System released“

gate ran into an obstacle or is too hard 

to move

check adjustment of forces, remove 

obstacle hence check if gate is easy 

to move

display: „photocell 

 

test negative“

interruption or hot-wired photocell

check correct connection hence 

remove obstacle > use status dispaly 

for help

display: „main safety edge

 

test negative“

(only when using the TX 310)

short-circuit or interruption of main 

safety edge

check correct connection hence bat

-

terry status of transmitter > use status 

dispaly for help

display: „side safety edge

 

test negative“

(only when using the TX 310)

short-circuit or interruption of side 

safety edge

check correct connection hence bat

-

terry status of transmitter > use status 

dispaly for help

display: „Low Voltage“

undervoltage

check supply line

display: „Error PULL T8 (T10) Slave“

the slave operator caused an error 

during the system check of main and 

side sensing edges

check correct connection of side sens

-

ing edge hence remove obstacle > use 

status dispaly for help 

no reaction when giving an impulse

no line voltage hence   

safety fuse broken

check line voltage as well as safety 

fuses

error of transmitter/control device/im-

pulse button,

e.g. transmitter not programmed

check transmitter/control device,

e.g. program transmitter and  

check battery

Содержание PULL T10





































Отзывы:

Нет отзывов