background image

Page -9-

PowerTouch Remote Control Systems - 814 Series (2 - 4) Functions

Manual C814.N2

Trouble Shooting Guide - 814 Series Remote Control

Use a digital or analog voltmeter to check power and voltage!

Do NOT use a test light

3.0  

No power to remote 

control receiver

3.1

  Logic ground or 

power connection to 
receiver has failed

3.2

  Chassis ground 

connection has failed

3.1a

  Check logic ground (black wire) and logic 

power (red wire).  Use a voltmeter probe when 
checking voltage.

3.1b

  If either ground or power is not present, then 

locate failure in wire harness and repair.

3.2a

  Check chassis ground connection, it should 

be clean and tight, no paint on metal, an external 
tooth star washer should be present, no rust or dirt 
in connection.

3.2b

  Chassis ground should be located on vehicle 

frame.

Symptom

Possible Cause

Corrective Action

4.0  

No signal (code) 

being transmitted

4.1

  Battery voltage low

4.2

  Transmitter is not 

sending a signal

4.3

  Transmitter code is 

incorrect

4.4

  Not all buttons send 

a signal when pressed.

4.1

  Check battery voltage.  Replace battery if 

voltage is 11.5 volts or less.  (Signal strength is 
dependent upon battery voltage.)

4.2

  Place probe from voltmeter on battery (+) and 

(-) leads.  Press any button, voltage should change 
by 0.2 to 0.3 volts if a signal is transmitted.  Check 
both buttons.

4.3a

  If transmitter is sending a signal and no 

signal is being received, re-code transmitter.

4.3b

  Send back to factory for re-coding.

4.4

  If a signal is not transmitted on all buttons, 

send back to factory for repair or replacement.

Symptom

Possible Cause

Corrective Action

5.0  

Poor range 0’ to 25’ 

(pulsating 0’ to 25’)

5.1

  Antenna damaged or 

grounded

5.1a

  Check antenna placement, it should not be 

touching any metal or tinted glass.

5.1b

  It should not be closer than 6’ to any motors 

or relays.

5.1c

  If it is coiled, then stretch it out and place 

near a window.

5.1d

  If antenna is cut or damaged, send back to 

factory for repair.

5.1e

  

NOTE:  Antenna can NOT be shortened or 

altered in any way

Symptom

Possible Cause

Corrective Action

Содержание PowerTouch 814 Series













Отзывы: