E
IR/S connector
(TLC Pro 521M only, see
figure 3
)—
This
two-pole 3.5 mm captive
screw connector can be configured to operate as a unidirectional serial port (figure 6,
1
)
or an IR port (figure 6,
2
). Pin 1= Signal (S), Pin 2= Ground (G).
S G
IR/S
S G
IR/S
S
G
(-)
(+)
(-)
(+)
(+)
(-)
To the IR Receiver of a
Projector, Display, or
Source Device
Two Single IR Emitters
Ground
IR Output Signal
Unidirectional
IR
or
IR or RS-232 Output
Ground
To a Projector,
Panel Display, or the
Wired IR Remote or
RS-232 Port of a
Source Device
IR/Serial Ports
Output options:
• IR (30 kHz to 300 kHz,
with or without carrier signals)
• Unidirectional RS-232
1
1
2
2
Figure 6.
TLC Pro 521M IR/S Connector
•
Serial port: Connect the port to the serial control receive (Rx) and ground pins of the
device to be controlled. The protocols are the same as the RS-232 connectors on the
previous page.
•
IR control: Connect this port directly to the wired IR port of another device. Or insert
the wires from up to four IR Emitters into an IR port and place the heads of the
emitters over or next to the IR signal pickup windows of the devices.
NOTE:
For the best IR control results, each emitter must be within 100 feet
(30 meters) of the TLC Pro 521M.
F
Reset LED
— This LED is in the center of the rear panel, to the right of the reset button. It
indicates power status and reset status of the device (see
Reset Modes
on page 26).
G
Reset button
— This recessed button is to the left of the Reset LED. Pressing the button
initiates the reset modes for the unit (see
Reset Modes
).
H
Network and Power over Ethernet (PoE) Connector
— This connector is in the right
side of the recessed area.
Connect the touchpanel to the
LAN using a twisted pair cable,
terminated with an RJ-45
connector. Use a straight-
through Ethernet cable to
connect the panel to a switch
or router. Use a crossover
cable to connect the panel
directly to a computer.
An Extron IPL Pro Control
Processor must also be
connected to the same
network domain as the
TLP Pro 520M (see
www.extron.com
for a list of
suggested models).
The TLC Pro 521M has an
integrated controller. No
external controller is required.
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
1
2
3
4
5
6
7
8
Ethernet
PC
Extron Devices
(Switchers, Scalers)
TCP/IP
Network
Crossover Cable
(for direct connection to a PC)
End 1
End 2
Pin
Wire Color
Pin Wire Color
1
white-orange
1
white-green
2
orange
2
green
3
white-green
3
white-orange
4
blue
4
blue
5
white-blue
5
white-blue
6
green
6
orange
7
white-brown
7
white-brown
8
brown
8
brown
T568B
T568A
LAN (Ethernet)
Default protocol, public ports:
• TLC Pro 521M IP address: 192.168.254.252
• TLP Pro 520M IP address: 192.168.254.251
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP: off
• DNS: 127.0.0.1
Touchpanel
LAN Port
IPL Pro Controller
(TLP Pro 520M only)
Figure 7.
Network and PoE Connector
TLP Pro 520M and TLC Pro 521M • Panel Features
11
Содержание TLC Pro 521M
Страница 6: ......
Страница 8: ...TLP Pro 520M and TLC Pro 521M Contents viii...