background image

Repairs to the patio heater may only be carried out by a qualified technician

 

PROBLEM   

 

 

SOLUTION 

 

Gas valve may be OFF

 

 

Turn the

 

gas valve ON 

 

LPG cylinder empty 

 

Refill

 

LPG cylinder

 

Orifice blocked

 

 

Clean or replace Orifice

 

Air in supply system 

 

Purge air from lines

  

Pilot will not light

 

Loose connection

  

Check all fittings

  

Debris around pilot  

Clean dirty area

  

Loose connection

 

 

Tighten connection

 

Thermocouple bad

  

Replace Thermocouple  

Gas leak in line  

Check connections

 

 

Pilot will not stay on

 

 

Lack of gas pressure  

LPG cylinder is near empty 

 

Gas pressure is low 

 

LPG cylinder is near empty 

 

Orifice blocked

 

 

Remove, clean and replace 

 

Control knob not ON 

 

Turn knob to ON 

Thermocouple bad

 

 

Replace Thermocouple 

 

Burner will not light

 

 

Pilot light assembly bent  
or not in correct location 

Place pilot light in correct positi on

  

and retry 

 

PROBABLE CAUSE

- 12 -

Distributed by: D.K.Gas Appliances. PO Box 34191 Erasmia 0023  

website: 

    email: [email protected]

www.totai.co.za

Issue 1-2018

TAMPERING:
Under no circumstances are you allowed to tamper with the jet sizes or modify anything on 
the appliance. Not only is it dangerous , it will also nullify your warranty

NOTE:

GAS-PRESSURE REGULATOR—This appliance is designed to operate on a gas pressure of 
2,8 kPa. A suitable regulator that complies with the requirements of SANS 1237 must be used 
with this appliance

TECHNICAL SPECIFICATIONS

Name

Specification

Model number

16/DK1027

Heat Output

11,0 kw

Gas Type

LPG

Jet sizes

Main burner 1,51 mm Pilot burner  0,22 mm

Operating Pressure

2,8 kPa

Gas consumtion (max.)

750 g/h

PROBLEMS CHECK LIST

Содержание 16/DK1027













Отзывы: