Toshiba TLCS-900 Series Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 178

background image

TOSHIBA CORPORATION

131

TMP96C141AF

Generating Timing

1) UART mode

Note:

Framing error occurs after an interrupt has occurred. Therefore, to check for framing error during interrupt operation, it is necessary to wait for 1 bit
period of transfer rate.

Receiving

Mode

9-Bit

8-Bit + Parity

8-Bit, 7-Bit + Parity, 7-Bit

Interrupt timing

Center of last bit (Bit 8)

Center of last bit (parity bit)

Center of stop bit

Framing error timing

Center of stop bit

Center of stop bit

Center of stop bit

Parity error timing

Center of last bit (Bit 8)

Center of last bit (parity bit)

Center of stop bit

Overrun error timing

Center of last bit (Bit 8)

Center of last bit (parity bit)

Center of stop bit

Transmitting

Mode

9-Bit

8-Bit + Parity

8-Bit, 7-Bit + Parity, 7-Bit

Interrupt timing

Just before last bit is transmitted.

←

←

11

➇

Transmission Buffer

Transmission buffer (SC0BUF/SC1BUF) shifts to and

sends the transmission data written from the CPU from
the least significant bit (LSB) in order, using transmission
shift clock TxDSFT which is generated by the transmis-
sion control. When all bits are shifted out, the transmis-
sion buffer becomes empty and generates INTTX0/
INTTX1 interrupt.

➈

Parity Control Circuit

When serial channel control register SC0CR <PE>/

SC1CR <PE> is set to “1", it is possible to transmit and
receive data with parity. However, parity can be added
only in 7-bit UART or 8-bit UART mode. With SC0CR
<EVEN>/SC1CR <EVEN> register, even (odd) parity can
be selected.

For transmission, parity is automatically generated

according to the data written in the transmission buffer
SCBUF, and data are transmitted after being stored in
SC0BUF <TB7>/SC1BUF <TB7> when in 7-bit UART
mode while in SCMOD <TB8>/SCMOD <TB8> when in
8-bit UART mode. <PE> and <EVEN> must be set
before transmission data are written in the transmission
buffer.

For receiving, data is shifted in the receiving buffer 1,

and parity is added after the data is transferred in the
receiving buffer 2 (SC0BUF/SC1BUF), and then com-
pared with SC0BUF <RB7>/SC1BUF <RB7> when in 7-

bit UART mode and with SC0MOD <RB8>/SC1MOD
<RB8> when in 8-bit UART mode. If they are not equal, a
parity error occurs, and SC0CR <PERR>/SC1CR
<PERR> flag is set

➉

Error Flag

Three error flags are provided to increase the reliabil-

ity of receiving data.

1. Overrun error <OERR>

If all bits of the next data are received in

receiving buffer 1 while valid data is stored in
receiving buffer 2 (SCBUF), an overrun error
will occur.

2. Parity error <PERR>

The parity generated for the data shifted

in receiving buffer 2 (SCBUF) is compared
with the parity bit received from RxD pin. If
they are not equal, a parity error occurs.

3. Framing error <FERR>

The stop bit of received data is sampled

three times around the center. If the majority
is “0", a framing error occurs.

«
...
129
130
131
132
133
...
»

Содержание TLCS-900 Series



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TLCS-900 Series

Бренд: Banner Страницы: 15

EtherNetIP ControlPlex CPC12EN

Бренд: E-T-A Страницы: 28

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Samson Страницы: 78

Бренд: ABB Страницы: 17

Бренд: Danfoss Страницы: 30

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Olsen Страницы: 4

Бренд: LAUNDRY SOLUTION Страницы: 14

Бренд: Levven Страницы: 2

Series RHCN-7000

Бренд: Omega Engineering Страницы: 2

Бренд: WAM Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Hoffer Страницы: 57

Бренд: Jung Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды