manualshive.com logo in svg

Toshiba TLCS-900 Series, Руководство пользователя

Серия Toshiba TLCS-900 - это надежные и производительные микроконтроллеры для различных приложений. Вы можете скачать бесплатное руководство по эксплуатации на нашем сайте. Посетите {веб-сайт} для загрузки.

Поделиться
Скачать
background image

 

TOSHIBA CORPORATION

 

143

 

TMP96C141AF

 

3.12.1 Operation

 

(1)

Analog Reference Voltage

High analog reference voltage is applied to the VREF 
pin, and low analog reference voltage is applied to 
AGND pin.
The reference voltage between VREG and AGND is 
divided by 1024 using ladder resistance, and com-
pared with the analog input voltage for A/D conversion.

(2)

Analog Input Channels

Analog input channel is selected by ADMOD <ADCH1, 
0>. However, which channel to select depends on the 
operation mode of the A/D converter.
In fixed analog input mode, one channel is selected by 
ADMOD <ADCH1, 0> among four pins: AN0 to AN3.
In analog input channel scan mode, the number of 
channels to be scanned from AN0 is specified by 
ADMOD <ADCH1, 0>, such as AN0

 

 →

 

 AN1, AN0 

 

→

 

 

AN1 

 

→

 

 AN2, and AN0

 

 →

 

 AN1 

 

→

 

 AN2 

 

→

 

 AN3.

When reset, A/D conversion channel register will be ini-
tialized to ADMOD <ADCH1, 0> = 00, so that AN0 pin 
will be selected.
The pins which are not used as analog input channel 
can be used as ordinary input port P5.

(3)

Starting A/D Conversion

A/D conversion starts when A/D conversion register 
ADMOD <ADS> is written “1". When A/D conversion 
starts, A/D conversion busy flag ADMOD <ADBF> 
which indicates “A/D conversion is in progress” will be 
set to “1".

(4)

A/D Conversion Mode

Both fixed A/D conversion channel mode and A/D 
conversion channel scan mode have two conversion 
modes, i.e., single and repeat conversion modes.
In fixed channel repeat mode, conversion of specified 
one channel is executed repeatedly.
In scan repeat mode, scanning from AN0, 

 

…

 

 

 

→

 

 AN3 is 

executed repeatedly.
A/D conversion mode is selected by ADMOD <REPET, 
SCAN>.

(5)

A/D Conversion Speed Selection

There are two A/D conversion speed modes: high 
speed mode and low speed mode. The selection is 
executed by ADMOD <ADCS> register.
When reset, ADMOD <ADCS> will be initialized to “0,” 
so that high speed conversion mode will be selected.

(6)

A/D Conversion End and Interrupt

• A/D conversion single mode

ADMOD <EOCF> for A/D conversion end will be 

set to “1,” ADMOD <ADBF> flag will be reset to “0,” 
and INTAD interrupt will be enabled when A/D conver-
sion of specified channel ends in fixed conversion 
channel mode or when A/D conversion of the last 
channel ends in channel scan mode.

• A/D conversion repeat mode

For both fixed conversion channel mode and con-

version channel scan mode, INTAD should be disabled 
when in repeat mode. Always set the INTE0AD at 
“000,” that disables the interrupt request.

Write “0” to ADMOD <REPET> to end the repeat 

mode. Then, the repeat mode will be exited as soon as 
the conversion in progress is completed.

(7)

Storing the A/D Conversion Result

The results of A/D conversion are stored in ADREG0 to 
ADREG3 registers for each channel. In repeat mode, 
the registers are updated whenever conversion ends.
ADREG0 to ADREG3 are read-only registers.

(8)

Reading the A/D Conversion Result

The results of A/D conversion are stored in ADREG0 to 
ADREG3 registers. When the contents of one of 
ADREG0 to ADREG3 registers are read, ADMOD 
<EOCF> will be cleared to “0".

Setting example:

When the analog input voltage of the 
AN3 pin is A/D converted and the 
result is stored in the memory 
address FF10H by A/D interrupt 
INTAD routine.

Содержание TLCS-900 Series



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TLCS-900 Series

OEG KMS Manual preview
KMS
Бренд: OEG Страницы: 168
IFM Electronic ecomat 100 R 360 Operating Instructions Manual preview
ecomat 100 R 360
Бренд: IFM Electronic Страницы: 16
IFM Electronic AC1331 Installation Instructions Manual preview
AC1331
Бренд: IFM Electronic Страницы: 23
OES ISC-9000 Operational Instructions preview
ISC-9000
Бренд: OES Страницы: 3
Parkside PDWE 8 A2 Operation And Safety Notes Translation Of The Original Instructions preview
PDWE 8 A2
Бренд: Parkside Страницы: 65
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Бренд: HEIDENHAIN Страницы: 257
Xilinx ML410 User Manual preview
ML410
Бренд: Xilinx Страницы: 101
U-Tron 6830-122-C10 Instruction Manual preview
6830-122-C10
Бренд: U-Tron Страницы: 8
Walchem WCT400 Series Instruction Manual preview
WCT400 Series
Бренд: Walchem Страницы: 43
Licht-Technik Mix4-6 Functional Description preview
Mix4-6
Бренд: Licht-Technik Страницы: 13
Ubiquiti Raspberry Pi 3B+ UniFi Controller Quick Start Manual preview
Raspberry Pi 3B+ UniFi Controller
Бренд: Ubiquiti Страницы: 4
CS-Lab CSMIO/IP-A Tuning Manual preview
CSMIO/IP-A
Бренд: CS-Lab Страницы: 20
Lennox M0STAT61Q-1 Installation & Operation Instructions preview
M0STAT61Q-1
Бренд: Lennox Страницы: 12
AKO Electronica AKO-14532 Manual preview
AKO-14532
Бренд: AKO Electronica Страницы: 2
Fuji Electric PXG5 Instruction Manual preview
PXG5
Бренд: Fuji Electric Страницы: 20
ARZAMAN SmartPID BBQ Easy User Manual preview
SmartPID BBQ Easy
Бренд: ARZAMAN Страницы: 27
PDK Red 2 Quick Start Manual preview
Red 2
Бренд: PDK Страницы: 2
AAT KaDe KDH-KS3012-IP Installation Manual preview
KaDe KDH-KS3012-IP
Бренд: AAT Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды