Toshiba TLCS-900 Series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 178

background image

TOSHIBA CORPORATION

117

TMP96C141AF

The serial channel has a buffer register for transmitting

and receiving operations, in order to temporarily store trans-
mitted or received data, so that transmitting and receiving
operations can be done independently (full duplex).

However, in I/O interface mode, SCLK (serial clock) pin is

used for both transmission and receiving, the channel
becomes half-duplex.

The receiving data register is of a double buffer structure

to prevent the occurrence of overrun error and provides one
frame of margin before CPU reads the received data. The
receiving data register stores the already received data while
the buffer register receives the next frame data.

By using CTS and RTS (there is no RTS pin, so any one

port must be controlled by software), it is possible to halt data
send until CPU finishes reading receive data every time a frame
is received (Handshake function).

In the UART mode, a check function is added not to start

the receiving operation by error start bits due to noise. The
channel starts receiving data only when the start bit is

detected to be normal at least twice in three samplings.

When the transmission buffer becomes empty and

requests the CPU to send the next transmission data, or when
data is stored in the receiving data register and the CPU is
requested to read the data, INTTX or INTRX interrupt occurs.
Besides, if an overrun error, parity error, or framing error occurs
during receiving operation, flag SC0CR/SC1CR <OERR,
PERR, FERR> will be set.

The serial channel 0/1 includes a special baud rate gen-

erator, which can set any baud rate by dividing the frequency
of four clocks (

φ

T0,

φ

T2,

φ

T8, and

φ

T32) from the internal pres-

caler (shared by 8-bit/16-bit timer) by the value 2 to 16.

In I/O interface mode, it is possible to input synchronous

signals as well as to transmit or receive data by external clock.

3.11.1 Control Registers

The serial channel is controlled by three control registers
SC0CR, SC0MOD, and BR0CR. Transmitted and received
data is stored in register SC0BUF.

«
...
115
116
117
118
119
...
»

Содержание TLCS-900 Series



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TLCS-900 Series

Бренд: C-TEC Страницы: 2

Бренд: Rain Bird Страницы: 138

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: Balboa Страницы: 2

Бренд: KEB Страницы: 16

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

SCENE MASTER - V1.0

Бренд: JBSYSTEMS Light Страницы: 24

Бренд: CALEFFI Страницы: 14

Бренд: SainSmart Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды