Toshiba TDP-MT5 Скачать руководство пользователя страница 11

Страница: 11 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the focus and zoom rings

The

focus ring

(505-0972-xx) fits around the front of the projection lens. The

zoom ring

(505-00974-xx)

fits behind the focus ring.

The lens cap (505-0841-xx) snaps onto the focus ring.

Both the focus ring and the zoom ring snap into place. They can be replaced without removing the front

bezel or top case.

Stand the projector lens side up on the work space.

Grasp the focus ring and pull it off of the lens barrel.

Grasp the zoom ring and pull it off of the lens barrel.

Assembly Notes

♦

Both rings have three slots or tabs that align with pins or slots on the lens barrel.

♦

Align the tabs on the zoom ring with the three slots on the lens barrel, and then press it into place. It

should fit close to the front bezel, but should not touch the bezel.

Содержание TDP-MT5













































































































Результаты поиска

Содержание TDP-MT5

Отзывы:

Похожие инструкции для TDP-MT5

Бренды по названию

Популярные бренды

Toshiba TDP-MT5, Руководство по обслуживанию

Результаты поиска

Содержание TDP-MT5

Отзывы:

Похожие инструкции для TDP-MT5

Бренды по названию

Популярные бренды