Toshiba TDP-MT5 Скачать руководство пользователя страница 3

Страница: 3 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Table of Contents

Table of Contents .......................................................................................................... 3

Safety Precautions ........................................................................................................ 5

Important Precautions .................................................................................................. 5

Important Safety Instructions ...................................................................................... 6

Introducing the TDP-T3, TDP-S3 and TDP-MT5 ......................................................... 7

Parts Replacement ........................................................................................................ 8

Replaceable Part Hierarchy ..................................................................................................8

Exploded views .....................................................................................................................9

Remove and replace the focus and zoom rings..................................................................11

Remove and the front bezel and front bezel vent ...............................................................13

Remove and replace the lamp door and lamp module .......................................................17

Remove and replace the top case ......................................................................................20

Remove and replace the keypad ........................................................................................23

Remove and replace the front fan.......................................................................................24

Remove and replace the speaker assembly .......................................................................26

Remove the controller ECA.................................................................................................29

Install the controller ECA.....................................................................................................32

Remove and replace the I/O EMI shield .............................................................................35

Remove and replace the chassis and power supply...........................................................36

Remove and replace the rear bezel ....................................................................................40

Remove and replace the chassis ........................................................................................43

Remove and replace the lamp fan ......................................................................................44

Remove and replace the lamp blower.................................................................................46

Remove and replace the power supply...............................................................................48

Remove and replace the power supply fan and safety switch cable...................................52

Remove and replace the power supply fuse .......................................................................54

Remove and replace the safety switch assembly ...............................................................55

Remove and replace the optical engine..............................................................................57

Remove and replace the bottom case ................................................................................59

Software ....................................................................................................................... 60

Downloading software to your computer.............................................................................60

Install the Software on the Computer..................................................................................61

Upgrading the software in the TDP-T3................................................................................64

Functional Tests.......................................................................................................... 70

Содержание TDP-MT5













































































































Результаты поиска

Содержание TDP-MT5

Отзывы:

Похожие инструкции для TDP-MT5

Бренды по названию

Популярные бренды

Toshiba TDP-MT5, Руководство по обслуживанию

Результаты поиска

Содержание TDP-MT5

Отзывы:

Похожие инструкции для TDP-MT5

Бренды по названию

Популярные бренды