Toshiba TDP-MT5 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 108

background image

TDP-S3/TDP-T3/TDP-MT5 Service Manual

70

Functional Tests

You perform the functional tests after you’ve repaired the projector to make sure all components of the

projector operate properly. You can also perform the functional tests if you’re having trouble determining

what is wrong with the projector. For additional help in diagnosing trouble with the projector, see

Troubleshooting on page 74.

Required equipment

Equipment

Notes

Composite video DVD player
with S-video capability

Make sure the video player has an S-video Out port and cables. The
player should also have a Composite video output port (RCA).

Toshiba strongly suggests you use a DVD player to test the
video quality.

DVD players reproduce colors better and project

sharper images. The least preferable is a VCR. If you must use a
VCR, make sure you use a commercially produced recording, not
one recorded from a broadcast source. The VCR must include an S-
video connector in addition to a composite connector.

Commercially produced
video to test S-video, composite
video, and audio.

You'll need the video in DVD, laser disc, or video cassette format.
Toshiba strongly suggests you use

Video Essentials, Optimizing

Your Audio/Video System

(DVD International, 1997).

Audio & Video cables

Use the cables that come with the projector, including the Digital
Video Interface (DVI) cable.

Computer cables

M1-A and M1-DA cables for both analog and digital playback.

RGB test screens in a
PowerPoint presentation

We recommend that you use the Test Patterns available on the
Toshiba website to check image quality.

PC with digital video and sound
card

Make sure the card has an M1 Digital Video Interface (DVI) output
port. The stereo audio card should have either a 3.5mm stereo
audio jack or RCA left and right output ports. The computer must
have a CD-ROM and a standard VESA connector for analog output.

Remote control

Ensure that the remote has fresh AA batteries.

Projection screen

Use a flat screen, not a curved one.

Before beginning

Make sure the work surface where you perform the functional tests is level and clean. Place the projector

on a soft surface (such as an anti-static mat) when running the tests.

Connect the following to the I/O panel on the projector:

♦

Video player through Composite Video and S-video ports

«
...
68
69
70
71
72
...
»

Содержание TDP-MT5













































































































Отзывы:

Нет отзывов

Похожие инструкции для TDP-MT5

Бренд: Panasonic Страницы: 11

Paragon Large Electrically Operated Projection Screen

Бренд: Draper Страницы: 2

Бренд: Navitar Страницы: 7

Бренд: Eiki Страницы: 1

Бренд: Eiki Страницы: 2

Бренд: M-system Страницы: 3

Бренд: Acer Страницы: 1

L811 EL8630Ua Series

Бренд: Acer Страницы: 53

Бренд: Acer Страницы: 24

QGD(7:1) R9840030

Бренд: Barco Страницы: 5

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 74

Бренд: Panasonic Страницы: 72

72HM196 - 72" Rear Projection TV

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды