Toshiba TDP-MT5 Скачать руководство пользователя страница 35

Страница: 35 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the I/O EMI shield

The

I/O EMI shield

(330-0703-xx) fits over the I/O connectors on the rear of the controller ECA. It fastens

to the controller with two jack screws.

You need to remove the controller ECA to access the I/O EMI shield.

Remove the Controller ECA (see page 29).

Remove the two 4-40 jack screws that fasten the EMI shield to the controller. The screws are

located on either side of the M1 connector.

Carefully pull the I/O EMI shield off of the connectors. Take care not to bend the shield or the

fingers as you work the shield off.

Assembly Notes

♦

Make sure the fingers on the shield contact the connectors.

♦

Torque the jack screws to 2 in-lbs (.226 Nm).

♦

For information about installing the controller ECA, see page 32.

Содержание TDP-MT5













































































































Результаты поиска

Содержание TDP-MT5

Отзывы:

Похожие инструкции для TDP-MT5

Бренды по названию

Популярные бренды

Toshiba TDP-MT5, Руководство по обслуживанию

Результаты поиска

Содержание TDP-MT5

Отзывы:

Похожие инструкции для TDP-MT5

Бренды по названию

Популярные бренды