Toshiba SureMark 4610 страница 87 Скачать руководство пользователя | Manualshive

Страница: 87 / 118

background image

Appendix A. 1NF fiscal ready printer

This section contains information on the SureMark 4610 Model 1NF point-of-sale fiscal ready printer. The
SureMark 4610 Model 1NF point-of-sale fiscal ready printer is a high-performance printer is based on
Toshiba 4610 technologies, incorporating a fiscal ready solution developed by Toshiba business partners
world wide having features and components that differ from the 4610 Model 1NF point-of-sale fiscal
printer.

Note:

All other information concerning the general remove and replace operations, and servicing of this
printer is the same as the 1NF fiscal printer. Refer to the appropriate sections in this publication for
information on general remove and replace operations.

Fiscal base

This section provides the information needed to remove and install the fiscal base from a fiscal ready
printer.

Removing the fiscal base from a fiscal ready printer

To remove the fiscal base, complete the following steps:

1. If necessary, remove the fiscal tray from the printer (see “Removing the fiscal tray” on page 28 for

information).

© Copyright Toshiba Global Commerce Solutions, Inc. 2013

69

«
...
85
86
87
88
89
...
»

Содержание SureMark 4610























































































































Отзывы:

Нет отзывов

Похожие инструкции для SureMark 4610

Бренд: Oki Страницы: 282

Бренд: MakerPi Страницы: 21

SCX-4300 - SCX 4300 B/W Laser

Бренд: Samsung Страницы: 97

SCX 4828FN - Laser Multi-Function Printer

Бренд: Samsung Страницы: 151

SCX 4725FN - B/W Laser - All-in-One

Бренд: Samsung Страницы: 120

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 97

SCX 4200 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 95

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 172

ProXpress M337x

Бренд: Samsung Страницы: 56

PROXPRESS M332 SERIES

Бренд: Samsung Страницы: 50

ML-2240 - 23 Ppm Mono Laser Printer

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 8

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 134

ML-1610 - B/W Laser Printer

Бренд: Samsung Страницы: 112

Бренд: Samsung Страницы: 128

Бренд: Samsung Страницы: 152

ML 3471ND - B/W Laser Printer

Бренд: Samsung Страницы: 207

ML 2150 - B/W Laser Printer

Бренд: Samsung Страницы: 237

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды