Toshiba SureMark 4610 страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 118

background image

Chapter 4. Running tests and diagnostics

This chapter describes the Diagnostics for POS Systems and Peripherals, off-line tests, and
troubleshooting procedures.

Testing the printer

The SureMark single station fiscal printer consists of a SureMark printer integrated with a fiscal logic card.
The printer card and fiscal logic card perform individual power on self tests. If both the printer POST and
the Fiscal logic POST are successful, the fiscal printer is ready for operation.

Printer POST:

1. The printer receives power through the fiscal logic and performs its POST.

2. Check the status of the printer-ready indicator:

v

Printer-ready indicator ON:

The printer POST completed successfully.

v

Printer-ready indicator OFF or blinking:

The printer POST failed.

3. If the Printer POST fails, see Troubleshooting.

4. If the Printer POST is successful, note the results of the fiscal logic POST.

Fiscal POST:

Fiscal POST failures are indicated by an error tone. Error tone definitions are provided in the
Troubleshooting section.

If either POST fails or if you suspect problems with your printer, see “Troubleshooting” on page 22

© Copyright Toshiba Global Commerce Solutions, Inc. 2013

21

|
|

«
...
37
38
39
40
41
...
»

Содержание SureMark 4610























































































































Отзывы:

Нет отзывов

Похожие инструкции для SureMark 4610

Бренд: Xerox Страницы: 34

Бренд: EasyThreed Страницы: 4

Бренд: EASYPRINT Страницы: 37

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 40

Бренд: Oki Страницы: 507

Бренд: Oki Страницы: 176

Бренд: Samsung Страницы: 351

Бренд: DNP Страницы: 2

Бренд: Savin Страницы: 160

Aficio SP C240SF

Бренд: Ricoh Страницы: 14

ColorQube 87 Series

Бренд: Xerox Страницы: 32

Бренд: GCC Technologies Страницы: 8

Бренд: Parkside Страницы: 104

634dte - X B/W Laser

Бренд: Lexmark Страницы: 148

Бренд: LulzBot Страницы: 3

Бренд: SPRT Страницы: 21

Бренд: Lexmark Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды