MECHANICAL ADJUSTMENTS
D2-2
1-4: CONFIRMATION OF VSR TORQUE
1.
2.
Install the Torque Gauge (JG002F) and Adapter (JG002B)
on the S Reel. Set to the Picture Search (Rewind) mode.
(Refer to Fig.1-4-B)
Then, confirm that it indicates 120~180gf•cm.
NOTE
If the torque is out of the range, replace the following parts.
2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM
Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because
of long term usage or failure, the confirmation and adjust-
ment are necessary.
NOTE
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
Fig. 2-1-A
CH-1
Envelope
(TP103)
CH-1
Track
CH-2
Track
CH-2
SW Pulse (TP102)
Fig. 2-1-B
Entrance
Max
Exit
Max
A
B
A : B
≥
3 : 2
NOTE
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) (Refer to Fig. 1-4-B)
1.
2.
3.
4.
Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
Move the Idler Ass’y from the S Reel.
Install the Torque Gauge (JG002F) and Adapter
(JG002B) on the S Reel. Turn the Torque Gauge
(JG002F) clockwise.
Then, confirm that it indicates 60~100gf•cm.
(T Reel Brake) (Refer to Fig. 1-4-B)
1.
2.
3.
4.
Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
Move the Idler Ass’y from the T Reel.
Install the Torque Gauge (JG002E) and Adapter
(JG002B) on the T reel. Turn the Torque Gauge
(JG002E) counterclockwise.
Then, confirm that it indicates 30~50gf•cm.
Fig. 1-4-A
The position at FF mode.
Stop at this position.
The position at
STOP mode.
Capstan DD Unit
Cassette Holder Ass’y
Cassette Opener
Pinch Roller Block
Fig. 1-4-B
Torque Gauge/Adapter
(JG002F/JG002B)
S Reel
T Reel
Torque Gauge/Adapter
(JG002E/JG002B)
Check item
1-4
Replacement Part
Idler Ass’y/Clutch Ass’y
S Reel side:
T Reel side:
S Reel/Tension Band/Tension
Connect/Tension Arm Ass’y
T Reel/T Brake Band//T Brake
Spring/T Brake Arm
1-5
2-1: GUIDE ROLLER
Playback the VHS Alignment Tape (Monoscope of ST-C6
MODE2).
Connect CH-1 of the oscilloscope to TP103 (Envelope)
and CH-2 to TP102 (SW Pulse).
Press and hold the ATR button on the remote control
more than 2 seconds to set tracking to center.
Trigger with SW Pulse and observe the envelope. (Refer
to Fig. 2-1-A)
When observing the envelope, adjust the Adjusting Driver
(JG005) slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
Adjust so that the A : B ratio is better than 3 : 2 as shown
in Fig. 2-1-B, even if you press the Tracking Button to
move the envelope (The envelope waveform will begin to
decrease when you press the Tracking Button).
Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
1.
2.
3.
4.
5.
6.
7.
