TEMPORARY OPERATION
11
In case of the misplaced or discharged remote control
•
Pressing the RESET button, the unit can start or stop
without using the remote control.
•
Operation mode is set on AUTOMATIC operation,
preset temperature is 24°C and fan operation is
automatic speed.
TIMER OPERATION
12
Daily timer allows the user to set both the ON & OFF timers and will be activated on a daily basis.
Setting the ON Timer
Setting the OFF Timer
1
Press
ON
: Set the desired ON timer.
Press
OFF
: Set the desired OFF timer.
2
Press
SET
: Set the timer.
Press
SET
: Set the timer.
3
Press
CLR
: Cancel the timer.
Press
CLR
: Cancel the timer.
• Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
• The setting will be saved for the next same operation.
Note:
Setting Daily Timer
1
Press
ON
: Set the ON timer.
3
Press
SET
.
2
Press
OFF
: Set the OFF timer.
4
Press
SET
button during the ( or )
mark
fl
ashing.
• During the daily timer is activating, both arrows ( , ) are indicated.
PRESET OPERATION
13
Set your preferred operation for future use. The setting will be memorized by the
unit for future operation (except air
fl
ow direction).
1. Select your preferred operation.
2. Press and hold
PRESET
for 3 seconds to memorize the setting. The
P
mark
displays.
3.
Press
PRESET
: Operate the preset operation.
AUTO RESTART OPERATION
14
To automatically restart the conditioner after the power failure (Power of the unit
must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set the
operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)
• Do not operate ON timer and OFF timer.
2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the
operation. (3 beep sound but OPERATION lamp does not blink)
To operate at super low fan speed for quiet operation (except in DRY mode)
Press
QUIET
: Start and stop the operation.
Note:
Under certain conditions, QUIET operation may not provide adequate
cooling or heating due to low sound features.
To save energy while sleeping, automatically control air
fl
ow and automatically
turn OFF.
Press
COMFORT
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
Note:
The cooling operation, the set temperature will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation, the set temperature will decrease.
QUIET OPERATION
15
COMFORT SLEEP OPERATION
16
SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)
19
OPERATION AND PERFORMANCE
20
1. Three-minute protection feature: To prevent the unit from being activated for
3 minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before the heating
operation starts.
3. Warm air control: When the room temperature reaches the set temperature,
the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoors and released into the
room. When the outdoor temperature is too low, use another recommended
heating apparatus in combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit
where it will not be subjected to snow drifts, accumulation of leaves or other
seasonal debris.
7. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of
plastic.
Note:
Item 2 to 6 for Heating model
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature
Room
Temperature
Heating
–15°C ~ 24°C
Less than 28°C
Cooling
0°C ~ 43°C
21°C ~ 32°C
Dry
0°C ~ 43°C
21°C ~ 32°C
The unit does not operate.
Cooling or Heating is abnormally low.
• The power main switch is turned off.
• The circuit breaker is activated to
cut off the power supply.
• Stoppage of electric current
• ON timer is set.
• The
fi
lters are blocked with dust.
• The temperature has been set improperly.
• The windows or doors are opened.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is FAN or DRY.
TROUBLESHOOTING (CHECK POINT)
21
REMOTE CONTROL A-B SELECTION
22
To separate using of remote control for each indoor unit in case of 2 air conditioner
are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3.
Push
and
hold
CHK
●
button on the Remote Control by the tip of the pencil. “00” will
be shown on the display.
4.
Press
MODE
during pushing
CHK
●
. “B” will show on the display and “00”
will disappear and the air conditioner will turn OFF. The Remote Control B is
memorized.
Note:
1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
To start the sleep timer (OFF timer) operation
Press
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
SLEEP TIMER OPERATION
17
Firstly, turn off the circuit breaker.
Filter Reset (Some models only)
FILTER lamp lights on; the
fi
lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
MAINTENANCE
18
To protect bad smell caused by the humidity in the indoor unit.
1.
If
the button is pressed once during “Cool” or “Dry” mode, the fan will
continue to run for other 20 minutes, then it will turn off automatically. This
will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the
3 times within 30 seconds.
Note:
• SELF CLEANING operation is default setting from factory.
• To cancel this function, press and hold the reset button on the indoor unit for
20 seconds.
The SELF CLEANING operation will be cancelled. (5 beep sound but
OPERATION lamp does not blink)
• Do the same to set this function again. (5 beep sound and OPERATION
lamp blink 5 time/sec for 5 seconds)
• AUTO RESTART operation will be cancelled by setting or cancellation of
SELF CLEANING operation. Set it again if necessary.
EN
Check whether the operation mode is different from what has been selected for
the units in the other rooms. (The following combinations of operations cannot be
performed: COOL and HEAT, DRY and HEAT, and PURE and HEAT.) Select the
same operation mode as for the other rooms.
1110250160.indb 3
1110250160.indb 3
4/22/09 3:40:52 PM
4/22/09 3:40:52 PM
