Toshiba MMY-MAP0804FT8-E страница 7 Скачать руководство пользователя

Страница: 7 / 37

– 6 –

Selection of installation place

Upon customer’s approval, install the air conditioner in a place which satisfies the following conditions:

• Place where it can be installed horizontally.
• Place which can reserve a sufficient service space for safe maintenance or checks.
• Place where there is no problem even if the drained water overflows.

Avoid the following places:

• Salty places (seaside area) or places with much gas sulfide (hot spring area) (If selecting such a place, special

maintenance is required.)

• Places where oil (including machine oil), steam, oil smoke or corrosive gas is generated.
• Places where iron or other metal dust is present. If iron or other metal dust adheres to or collects on the interior

of the air conditioner, it may spontaneously combust and start a fire.

• Places where an organic solvent is used.
• Chemical plants with a cooling system using liquid carbon dioxide.
• Places where a device generating high frequency (inverter, non-utility generator, medical apparatus, or

communication equipment) is set. (Malfunction or abnormal control of the air conditioner, or interference to
devices listed above may occur.)

• Places where discharged air from the outdoor unit blows against the windows of a neighbour's house.
• Places unable to bear the weight of the unit.
• Places with poor ventilation.
• Places where ambient temperature falls below -15°C for more than 72 hours running. The outdoor heat

exchanger may be damaged by the frost.

The cooling performance may decline considerably when total operating capacity of cooling indoor units is less
than 4HP while ambient temperature is below 0°C.



Installation space

Leave space necessary for running, installation and servicing.

NOTE

• If there is an obstacle above the outdoor unit, leave a space of 2000 mm or more to the top end of the outdoor

unit.

• If there is a wall around the outdoor unit, make sure that its height does not exceed 800 mm.

Air discharge

Air

intake

Air intake

Air

intake

Air intake

Installation /

servicing

surface

Square hole for

handling

Outdoor unit top view

10 mm or

500 mm or

(Rear side)

10 mm or

500 mm or

(Front side)

20 mm or more

▼

Combination of outdoor units

Equivalent HP

Model name of

outdoor unit

MMY-

Combination of outdoor unit MMY-

Unit 1

Unit 2

Unit 3

8 HP

MAP0804

✽

MAP0804

✽

–

10 HP

MAP1004

✽

MAP1004

✽

–

12 HP

MAP1204

✽

MAP1204

✽

–

14 HP

MAP1404

✽

MAP1404

✽

–

16 HP

AP1614

✽

MAP0804

✽

MAP0804

✽

–

18 HP

AP1814

✽

MAP1004

✽

MAP0804

✽

–

20 HP

AP2014

✽

MAP1004

✽

MAP1004

✽

–

22 HP

AP2214

✽

MAP1204

✽

MAP1004

✽

–

24 HP

AP2414

✽

MAP1404

✽

MAP1004

✽

–

26 HP

AP2614

✽

MAP1404

✽

MAP1204

✽

–

28 HP

AP2814

✽

MAP1404

✽

MAP1404

✽

–

30 HP

AP3014

✽

MAP1004

✽

MAP1004

✽

MAP1004

✽

32 HP

AP3214

✽

MAP1204

✽

MAP1004

✽

MAP1004

✽

34 HP

AP3414

✽

MAP1404

✽

MAP1004

✽

MAP1004

✽

36 HP

AP3614

✽

MAP1204

✽

MAP1204

✽

MAP1204

✽

38 HP

AP3814

✽

MAP1404

✽

MAP1204

✽

MAP1204

✽

40 HP

AP4014

✽

MAP1404

✽

MAP1404

✽

MAP1204

✽

42 HP

AP4214

✽

MAP1404

✽

MAP1404

✽

MAP1404

✽

11-EN

12-EN

Содержание MMY-MAP0804FT8-E






































Результаты поиска

Содержание MMY-MAP0804FT8-E

Отзывы:

Похожие инструкции для MMY-MAP0804FT8-E

Бренды по названию

Популярные бренды

Toshiba MMY-MAP0804FT8-E, Руководство по установке

Результаты поиска

Содержание MMY-MAP0804FT8-E

Отзывы:

Похожие инструкции для MMY-MAP0804FT8-E

Бренды по названию

Популярные бренды