Toshiba EB621 Скачать руководство пользователя страница 66

Страница: 66 / 122

model 2000 Ethernet Module Operation Manual

Chapter 4 Installation and Wiring

4.5 12 VDC Power Cable Connection

The EN611, EN621 or EB621 receives an ex12 VDC for AUI transceivers at its
connector CN2 through the +12 V power cable.

The +12 VDC power cable has a crimp terminal 3 mm in diameter. Connect it to the +12
VDC power supply.

Applicable models: EN611, EN621, EB621

Figure 4-9 Conn12 VDC Power Cable

Warning

• Be sure to use the s12 VDC power cable supplied with the product.

• Make sure of the polarities in connecting the +12 VDC power cable. Otherwise, it may

cause not only product trouble, but smoke and a fire.

• Do not apply 100 VAC to the +12 VDC power cable by mistake. Otherwise, it may cause

smoke or a fire.

Caution

• Use a separate power source to supply power to the 12 VDC power connector CN2 on each

Ethernet module. In cases where it is not possible to use separate power sources, wire the
power cable in such a way that each Ethernet module can be separately switched off.

• Use a +12 VDC power supply with a protective circuit.

+12 VDC
power cable

EN6
or
EB6 module

2P connector (CN2)
for receiving
+12 VDC

･

0 V

･

12 Vdc

Содержание EB621



























































































































Результаты поиска

Содержание EB621

Отзывы:

Похожие инструкции для EB621

Бренды по названию

Популярные бренды

Toshiba EB621, Руководство по эксплуатации

Результаты поиска

Содержание EB621

Отзывы:

Похожие инструкции для EB621

Бренды по названию

Популярные бренды