manualshive.com logo in svg

Toshiba EB621, Руководство по эксплуатации

Поделиться
Скачать
Toshiba EB621 Скачать руководство пользователя страница 36

24

model 2000 Ethernet Module Operation Manual

Chapter 3 Setting

3

3.2.3

Multicast address summary

The EN6 module supports 15 multicast addresses, which are as shown in the table 
below.

Any of these 15 addresses can be selected and registered per EN611 to EN641 module 
as desired. Any15 addresses in all multicast addresses (224.0.0.0 - 239.255.255.255) 
can be selected and registered per EN651, EN651A, EN661 module as desired. 

Note:

Addresses 224.0.0.0 to 239.255.255.255 are restricted in local network usage.
The packets destined to these addresses are not transferred by router. Because
there are some multicast addresses, confirming used addresses is needed.

Use the Engineering tool to register them in the EN6 module.

For how to register them, refer to the description of setting with the Engineering tool.

Figure 3-4 Multicast Group Configuration

Table 3-5  Multicast Address

No.

Multicast Address

1

225.224.0.1

2

225.224.0.2

3

225.224.0.3

4

225.224.0.4

5

225.224.0.5

6

225.224.0.6

7

225.224.0.7

8

225.224.0.8

9

225.224.0.9

10

225.224.0.10

11

225.224.0.11

12

225.224.0.12

13

225.224.0.13

14

225.224.0.14

15

225.224.0.15

Содержание EB621



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды