Toshiba E-studio 556 Скачать руководство пользователя страница 89

Страница: 89 / 104

7.CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error Codes 87

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error codes on transmission and reception

4313

Not authorized to store in e-Filing

The user has not been authorized to perform this operation. Ask your
administrator.

4314

Not authorized to send a Fax/iFax

The user has not been authorized to perform this operation. Ask your
administrator.

4321

Not authorized to perform printing in the
specified setting

The user has not been authorized to perform this operation. Ask your
administrator.

4411

Image data generation failure

Check if the file to be printed is broken. Perform printing again or use
another printer driver.

4412

Double-sign encoding error

A double-sign encoding error occurred because the PDF file is encrypted
in unsupported script. Printing the file in this function is impossible.

4611

Font download failure

Since the available number of fonts is exceeded, the font cannot be
registered. Delete at least one font.

4612

Font download failure

Since there is no space in HDD, the font cannot be registered. Delete at
least one font.

4613

Font download failure

Since an error has occurred, the font cannot be registered. Perform
downloading again or regenerate the font data first.

4621

Downloaded font deletion failure

Check if the font to be deleted is registered.

Error Code

Problem Description

Corrective Action

Error Code

Problem Description

Corrective Action

0012

Original misfeed

Remove the misfed original.

0013

Door open

Firmly close the open door.

0020

Power interruption

Check the power interruption report.

0030

Interruption by paper misfeeds during
direct transmission

Remove the misfed paper and reattempt the transmission.

0033

Polling Error

Check polling options setup (Security Code, etc.), and check whether the
polling document exists.

0042

Memory full

Make sure that there is sufficient memory before making the call again.

0050

Line busy

Reattempt the communications.

0053

Security Mismatch in Relay or Mail Box
transmission

Confirm the remote party’s Security Code, system password and your
setup.

00B0-

00B500C0-

00C400D0-

00D2

Signal Error or Line Condition Error

Reattempt the communications.

00E8

HDD error

Reattempt the communications. If the error still persists, contact your
service representative.

00F0

Software failure

Reattempt the communications. If the error still persists, contact your
service representative.

00F1

Hardware noise

Reattempt the communications. If the error still persists, contact your
service representative.

1C10

System access abnormality

Turn the power OFF and then back ON. Perform the problem job again. If
the error still persists, contact your service representative.

1C11

Insufficient memory

Complete any running jobs first before performing the job in error. If the
error still persists, turn the power OFF and then back ON, and try again.

1C12

Message reception error

Turn the power OFF and then back ON. Perform the job in error again.

1C13

Message transmission error

Turn the power OFF and then back ON. Perform the job in error again.

1C14

Invalid parameter

If a template is being used, create it again. If the error still persists, turn
the power OFF and then back ON, and try again.

1C15

Exceeding file capacity

Ask your administrator to change the “Fragment Page Size” setting for
the Internet Fax setting, or reduce the number of pages and try again.

1C30-1C33

Disk access error

Complete any running jobs first before performing the job in error. If the
error still persists, turn the power OFF and then back ON, and try again.

1C40

Image conversion abnormality

Turn the power OFF and then back ON. Perform the job in error again. If
the error still persists, contact your service representative.

Содержание E-studio 556








































































































Результаты поиска

Содержание E-studio 556

Отзывы:

Похожие инструкции для E-studio 556

Бренды по названию

Популярные бренды

Toshiba E-studio 556, Руководство по устранению неисправностей

Результаты поиска

Содержание E-studio 556

Отзывы:

Похожие инструкции для E-studio 556

Бренды по названию

Популярные бренды