Toshiba E-studio 556 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 104

background image

1.TROUBLESHOOTING FOR THE HARDWARE

Replacing a Toner Cartridge 41

1 TROUBLESHOOTING FOR THE HARDWARE

Never attempt to incinerate toner cartridges.

Dispose of used toner cartridges in accordance with local regulations.

y

You can replace a toner cartridge while the print function is in operation when “Open the toner cover Install new
toner cartridge” is displayed.

y

Some toner is still left in the toner cartridge while the message “Toner near Empty” is displayed. You do not have to
replace the toner cartridge yet, but if you choose to do so, follow the procedure

P.43 “Replacing a “Near Empty”

toner cartridge”. This procedure is needed to reset the toner counter to display the next “Toner near Empty”
message at the proper time.

Recommended toner cartridges

To assure optimal printing performance, we recommend that you use only genuine TOSHIBA toner cartridges. If you
use a TOSHIBA-recommended toner cartridge, you can utilize the following two functions of this equipment:

Cartridge detecting function:

This function checks if the toner cartridge is correctly installed and notifies you if it is not.

Toner remaining check function:

This function notifies you when there is little toner remaining in the cartridge, as well as notifying it to your authorized
service representative automatically by the remote service.

If you are using a toner cartridge other than the one we recommend, the equipment may not be able to detect whether
it is installed or not. Therefore, even if the toner cartridge is correctly installed, the error message “TONER NOT
RECOGNIZED” appears on the touch panel and printing may not be performed. You may also not be able to utilize the
toner remaining check function and the remote service function notifying your authorized service representative
automatically.
If you are using a toner cartridge other than the one we recommend, toner is not recognized. If this is a problem for
you, please contact your service representative. Remember you will not be able to utilize the cartridge check function
as we mentioned.

1

Open the toner cover on the front of the equipment.

2

Hold the green handle and pull the toner cartridge
holder toward you.

«
...
41
42
43
44
45
...
»

Содержание E-studio 556









































































































Отзывы:

Нет отзывов

Похожие инструкции для E-studio 556

Бренд: Xerox Страницы: 24

CLP-680ND: CLP-775ND

Бренд: Samsung Страницы: 2

Бренд: Oki Страницы: 268

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 202

Бренд: Oki Страницы: 201

Бренд: Oki Страницы: 103

Бренд: Oki Страницы: 256

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 63

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 616

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 138

Microline 320 Turbo D1

Бренд: Oki Страницы: 2

ML320 Epson/IBM

Бренд: Oki Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды