Toshiba D-VR18DTKB, Руководство пользователя

Страница: 33 / 96

33
EN
Int
rod
uct
ion
Co
nn
ect
ion
s
Basic Setup
Pl
ayback
Ed
iti
n
g
V
CR Fu
ncti
on
s
O
th
ers
Fu
nc
ti
on
Set
u
p
Recordi
n
g
Setting the Clock
Auto Clock Setting
This unit receives time signals from the analogue /
DVB channels, and sets the clock automatically. Set
the channel tuning before setting Auto Clock.
1
In stop mode, press [SETUP]. Select
“General Setting” using [
U / D ],
then press [ENTER / OK].
2
Select “Clock” using [ U / D ], then
press [ENTER / OK].
3
Select “Auto Clock Setting” using
[
U
/
D
], then press [ENTER / OK].
• If any DVB channel has been set, the auto clock
is on. “Auto Clock Setting” will be displayed in
grey and you cannot select it.
4
Select “ON” using [
U
/
D
], then
press [ENTER / OK].
The current time will be set automatically.
5
Press [SETUP] to exit.
6
Press [ ON / STANDBY] to turn
off.
The Auto clock function is activated.
• This unit will search for the time every time
when the power is turned off.
• Leave the unit off for several minutes to give it
time to set the clock.
Hint
• If you want to cancel “Auto Clock Setting”, select
“OFF” using [ U / D ] , and then press [ENTER / OK]
at the step 4.
Note
• The default setting of “Auto Clock Setting” is “ON”.
• The clock may set itself automatically after you
connect the antenna cable to the unit and plug in the
mains cable. In this case, the current time will
appear on the front panel display.
• If there are only analogue channels memorised in
this unit:
- The channel assigned to “904” must receive the
PDC signal in order to set the clock automatically.
- The unit will correct the current time by receiving
PDC broadcasts whenever the power is turned off.
- Between 23:00 and 1:00, the Auto Clock function
will not operate even when the power is turned off.
• The clock cannot be set automatically if you are not
receiving a channel in your area that carries a time
signal. In this case, set the clock manually.
• The unit will also correct the current time
automatically at 8:00 and 1:10 if the unit is in
standby mode or if you are watching DVB channel.
Manual Clock Setting
1
In stop mode, press [SETUP]. Select
“General Setting” using [
U
/
D
],
then press [ENTER / OK].
2
Select “Clock” using [
U
/
D
], then
press [ENTER / OK].
3
Select “Clock Setting” using [ U / D ],
then press [ENTER / OK].
Default date will appear.
4
Press [ENTER / OK] again.
5
Enter the date (day / month / year)
using [
U
/
D
].
Press [
P
] to move the cursor to the next field. If
you want to go back to the previous field, press
[ L ] .
6
Enter the time (hours / minutes)
using [
U
/
D
], then press
[ENTER / OK].
The clock will start.
• Although seconds are not displayed, they will be
counted from zero.
7
Press [SETUP] to exit.
Note
• Your clock setting will be lost if either there is a
power failure or the unit is unplugged for more than
30 seconds.
• If you have set the timer recording, “Clock” will be
displayed in grey and you cannot select it.
General Setting
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
Reset All
Clock Setting
01 / 01 / 2008 ( TUE )
0 : 00
E9NG1BD_EN.book Page 33 Tuesday, April 8, 2008 6:21 PM