Toshiba AW-B1000GM, Руководство пользователя

Страница: 15 / 20

15
Attaching the water inlet hose to the faucet
If you attach the water inlet hose completely, it may cause a water leakage.
Faucet shape Wall-mounted faucets are best.
The distance is needed
1.6 cm or more
Attaching the hose union
1
Push the lock lever of the water
supply hose. Pulling the sleeve down,
lower the entire hose to disconnect the
hose union.
2 Check the diameter of the faucet.
When the faucet mouth is large,
loose the screws and remove the
inside ring to facilitate, attachment.
3 Loose 4 screws of the hose union,
push the hose union to the water
faucet.
4 Tighten the four screws evenly around
the faucet. In this time check the gap
is approx. 4 mm between the nozzle
and the ring.
5 Remove the seal from the union
and turn to the arrow destination
the nozzle to tighten securely.
6 Check the gap is approx. 1 to
3 mm between the nozzle and
the ring.
•
If the gap is wide, it may cause the water leak.
•
If it cause the water leakage during operation,
tighten the nozzle more securely.
Caution
•
If you attach the hose union again because of
moving house etc., loose the gap is approx. 4 mm
between the nozzle and the
ring. Then attach it according
above methods.
They are
preventable the water leakage.
1 Pull the sleeve down, then insert
the water inlet hose.
2 Separate the sleeve until a click is
heard, then push it up.
3 Check to ensure that the lock
lever is hung on the nozzle. Next,
check to ensure that the water
supply hose does not come off by
pulling down on it.
4 Tighten the hose nut
on the end of the water
inlet hose securely to
the water inlet valve.
Caution:
•
Check to ensure that the water
inlet hose is properly installed by
turning the water on and checking
for leakage.
If there is leakage, connect it from the
fi rst.
•
If you remove the water inlet
hose after supplying water, water
may splash. Refer to the following
— “Removing the water inlet hose”.
Wall-mounted
shaped Square
faucet Movable
faucet Multi-home
faucet
Joint
seal
Hose Union
Lock
lever
Water
inlet
hose
Ring
Inside
ring
Approx.
4 mm.
Sleeve
Sleeve
Caution
•
The old inlet hose should not be reused.
•
If the faucets are not suited, please contact your dealer.
•
Do not connect the hot water supplying convenience.
•
In order to provide a permanent source of water
for your washing machine, it is suggested
that a branching water pipe (available separately)
be
used.
Hose union
Branching
water pipe
Installing the drainage hose
Moving the hook
•
When inserting the drainage hose into a wash pan or onto a
drain pipe, the hook may be moved to facilitate the installation.
•
When hooking the hose hook into the
slot provided on the body of your
washing machine, move the hook
back to its initial position.
•
Insert the drainage hose in as far as
it will go, then use the accessory
hose band to secure it tightly.
•
Secure the hose tightly. An improperly
secured hose may cause leakage.
•
Lock hose band distance to cabinet
about 10 mm as fi gure.
•
When attaching the drainage hose to a wash
pan, etc., either leave a gap between the end
of the hose and the adjacent surface, or cut
the hose diagonally to ensure proper drainage.
※ Allowing the fl at end of the hose to come in
contact with the fl at surface of the washing
machine will impair drainage.
Caution:
•
If the level of the threshold and the
drainage hose is high, the washing
machine may not be drained.
•
Be careful not to rub the drainage hose. Do not insert the
drainage hose under the washing machine. They may be
damaged the drainage hose.
Drainage hose extension
•
Pay close attention to the height of the drainage hose and
articles over which it passes. If the drainage hose is too high,
proper drainage may not be obtained.
•
The length of the drainage hose
may be extended to as much
as 3 m if kept the same level.
10 mm
Hook
Hose-band
Drain outlet
Drainage hose
Concrete block
Drainage hose
Gap
3 cm or
greater
Cut diagonally
Drainage hole
Drainage hose
15 cm or less
Drainage hose cap
3 m or less
Approx.
1 to 3 mm
Nozzle
Ring
Approx.
4 mm
Nozzle
Lock
lever
Installing the ground pin
•
The ground pin in the plug should be connected to the proper point of the socket for grounding.
Inlet hose
Hose nut
Water inlet valve
Connecting the water inlet hose