Toro Z500 Series Z Master Скачать руководство пользователя страница 55

Страница: 55 / 64

Important:

The grass deﬂector must be

able to lower down into position. Lift the
deﬂector up to test that it lowers into the
full down position.

Figure 73

1. Bolt

5. Spring installed

2. Spacer

6. Grass Deector

3. Locknut

end of spring, place

behind deck edge before

installing bolt

4. Spring

hook end of spring

Cleaning

Cleaning Under the Mower

Remove the grass buildup under the mower daily.

1. Disengage the PTO, move the motion control

levers to the neutral locked position and set
the parking brake.

2. Stop the engine, remove the key, and wait for

all moving parts to stop before leaving the
operating position.

3. Raise the mower to the transport position.

Waste Disposal

Engine oil, batteries, hydraulic oil, and engine
coolant are pollutants to the environment.
Dispose of these according to your state and local
regulations.

Содержание Z500 Series Z Master

































































Результаты поиска

Содержание Z500 Series Z Master

Отзывы:

Похожие инструкции для Z500 Series Z Master

Бренды по названию

Популярные бренды

Toro Z500 Series Z Master, Руководство оператора

Результаты поиска

Содержание Z500 Series Z Master

Отзывы:

Похожие инструкции для Z500 Series Z Master

Бренды по названию

Популярные бренды