Toro Z500 Series Z Master Скачать руководство пользователя страница 49

Страница: 49 / 64

Figure 62

1. Tracking knob

3. Adjustment bolt

2. Pump rod

4. Yoke

3. Move the motion control lever forward and

reverse, then back to neutral. The wheel must
stop turning or slightly creep in reverse.

4. Open the throttle to fast. Make sure wheel

remains stopped or slightly creeps in reverse,
adjust if necessary.

Setting the Left-hand Hydraulic Pump

Neutral Position

1. Loosen the locknuts at the ball joints on the

pump control rod (Figure 63).

Figure 63

1. Clevis pin in slot

7. Spring

2. Nut against yoke

8. Pivot shaft

3. Adjustment bolt

9. Yoke

4. Pump rod

10. Locknut

5. Double nuts

11. Ball joint

6. Jam nut

2. Start the engine, open throttle 1/2 way, and

release parking brake. Refer to Starting and
Stopping the Engine in Operation, page 15.

Note:

The motion control lever must be in

neutral while making any adjustments.

Note:

The front nut on the pump rod has

left-hand threads.

3. Adjust the pump rod length by rotating double

nuts on rod, in the appropriate direction,
until wheel is still or slightly creeps in reverse
(Figure 63).

4. Move the motion control lever forward and

reverse, then back to neutral. The wheel must
stop turning or slightly creep in reverse.

5. Open the throttle to fast. Make sure the wheel

remains stopped or slightly creeps in reverse,
adjust if necessary.

6. Tighten the locknuts at the ball joints

(Figure 63).

Содержание Z500 Series Z Master

































































Результаты поиска

Содержание Z500 Series Z Master

Отзывы:

Похожие инструкции для Z500 Series Z Master

Бренды по названию

Популярные бренды

Toro Z500 Series Z Master, Руководство оператора

Результаты поиска

Содержание Z500 Series Z Master

Отзывы:

Похожие инструкции для Z500 Series Z Master

Бренды по названию

Популярные бренды