Toro Z500 Series Z Master Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 64

background image

Figure 47

1. Engine screen

2. Oil cooler

Cleaning the Engine Fins

Every 100 hours clean the engine cylinder and
cylinder head cooling ﬁns. Also clean around
carburetor, governor levers and linkage. This will
make sure adequate cooling to hydraulic pumps,
motors and engine and will reduce the possibility
of overheating and mechanical damage.

1. Remove the engine shroud.

2. Clean the engine cooling ﬁns.

3. Install the engine shroud.

Figure 48

1. Panel

3. Screws

2. Engine shroud

Brake Maintenance

Adjusting the Parking Brake

Check the parking brake for proper adjustment.

1. Disengage brake lever (lever down).

2. Measure the length of the spring.

The measurement should be 2-3/4 inch (70
mm) between washers (Figure 49).

Figure 49

1. Brake lever

4. Collar on brake rod

2. Spring (2-3/4 inches/70

mm)

5. 3/16–1/4 inch (5–7 mm)

3. Adjusting nuts

6. Jam nut and yoke

3. If adjustment is necessary, loosen the jam nut

below the spring and tighten the nut directly
below the yoke (Figure 49). Turn the nut until
the correct measurement is obtained. Tighten
the two nuts together and repeat on opposite
side of unit.

4. Turn nuts clockwise to shorten spring length

and turn counter-clockwise to lengthen the
spring.

5. Engage parking brake, lever up.

6. Measure the distance between the trunnion

roller and the collar on brake rod.

The measurement should be 3/16-1/4 inch
(5-7 mm) (Figure 49).

7. If adjustment is necessary, loosen the jam nut

directly below the yoke. Turn the bottom rod
until the correct measurement is obtained
(Figure 49). Tighten jam nut at yoke

Belt Maintenance

Inspecting the Belts

Inspect all belts every 100 hours.

Check belts for cracks, frayed edges, burn marks
or any other damage. Replace damaged belts.

Replacing the Mower Belt

Squealing when the belt is rotating, blades slipping
when cutting grass, frayed belt edges, burn marks
and cracks are signs of a worn mower belt. Replace

41

«
...
39
40
41
42
43
...
»

Содержание Z500 Series Z Master

































































Отзывы:

Нет отзывов

Похожие инструкции для Z500 Series Z Master

Бренд: Ybravo Страницы: 2

YT2050 (1694637)

Бренд: Snapper Страницы: 74

Бренд: MasterCraft Страницы: 24

Wheel Horse 265-6

Бренд: Toro Страницы: 44

Бренд: Ryobi Страницы: 8

Бренд: Qualcast Страницы: 20

Бренд: MTD Страницы: 12

GTTAC51T-BS675RT16

Бренд: Gardeo Страницы: 115

Бренд: Toro Страницы: 24

309006 190A Series

Бренд: Murray Страницы: 40

Бренд: Sabo Страницы: 100

Бренд: Lastec Страницы: 23

Бренд: Qualcast Страницы: 2

Бренд: Yard-Man Страницы: 6

Бренд: Brinly Страницы: 28

Бренд: Cramer Страницы: 9

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды