Toro Z500 Series Z Master Скачать руководство пользователя страница 31

Страница: 31 / 64

How to Grease

1. Disengage the PTO, move the motion control

levers to the neutral locked position and set
the parking brake.

2. Stop the engine, remove the key, and wait for

all moving parts to stop before leaving the
operating position.

3. Clean the grease ﬁttings with a rag. Make

sure to scrape any paint off the front of the
ﬁtting(s).

4. Connect a grease gun to the ﬁtting. Pump

grease into the ﬁttings until grease begins to
ooze out of the bearings.

5. Wipe up any excess grease.

Greasing the Front Caster Pivots

Lubricate the front caster pivots once a year.

1. Remove the dust cap and adjust the caster

pivots. Keep the dust cap off until greasing
is done. Refer to Adjusting the Caster Pivot
Bearing in Drive System Maintenance, page 39.

2. Remove the hex plug. Thread a grease zerk

into the hole.

3. Pump grease into the zerk until it oozes out

around the top bearing.

4. Remove the grease zerk in the hole. Install the

hex plug and cap.

Where to Add Grease

Lubricate the grease ﬁttings as shown on the
Check Service Reference Aid decal (Figure 30).

Figure 30

Where to Add Light Oil or Spray

Lubrication

Lubricate the machine in the following areas with
spray type lubricant or light oil. Lubricate every
150 hours.

•

Seat switch actuator.

•

Brake handle pivot.

•

Brake rod bushings.

•

Motion control bronze bushings.

Greasing the Bearings

Lubricate the cutting machine after every
50 operating hours. Grease with No. 2
general-purpose lithium-base or molybdenum-base
grease.

1. Disengage the PTO, move the motion control

levers to the neutral locked position, and set
the parking brake.

2. Stop the engine, remove the key, and wait for

all moving parts to stop before leaving the
operating position.

3. Grease the ﬁttings on the 3 spindle bearings

(Fig. 38).

Содержание Z500 Series Z Master

































































Результаты поиска

Содержание Z500 Series Z Master

Отзывы:

Похожие инструкции для Z500 Series Z Master

Бренды по названию

Популярные бренды

Toro Z500 Series Z Master, Руководство оператора

Результаты поиска

Содержание Z500 Series Z Master

Отзывы:

Похожие инструкции для Z500 Series Z Master

Бренды по названию

Популярные бренды