Toro TimeCutter ZD530 Скачать руководство пользователя | Manualshive

Страница: 43 / 52

background image

Cleaning

Cleaning the Collection

Sensors

The collection sensors do not require any
scheduled maintenance, however; in the event
that the collection bag alarm goes off and the bag
is less than full, gently wipe off the faces of the
sensors with a soft cloth. The cloth can be damp
with water.

Important:

Do not use solvents or chemicals

of any kind to clean the face of the sensors.

When ﬁnished using the machine, use a soft
cloth to clear away blockage between the sensors
(crusted or clumped up grass clippings or leaves).

Washing the Underside of

the Mower

After each use, wash the underside of the mower
to prevent grass buildup for improved mulch
action and clipping dispersal.

1. Park the machine on a level surface and

disengage the blade control switch.

2. Move the motion control levers to the brake

position, stop the engine, remove the key, and
wait for all moving parts to stop before leaving
the operating position.

3. Attach the hose to the end of the mower

washout ﬁtting, and turn the water on high
(Figure 61).

Note:

Spread petroleum jelly on the washout

ﬁtting O-ring to make the hose slide on easier
and protect the O-ring.

Figure 61

1. Washout tting

3. Hose

2. Mower deck

4. Lower the mower to the lowest height-of-cut.

5. Sit on the seat and start the engine. Engage the

blade control switch and let the mower run for
one to three minutes.

6. Disengage the blade control switch, stop the

engine, and remove the ignition key. Wait for
all moving parts to stop.

7. Turn the water off and remove the hose from

the washout ﬁtting.

Note:

If the mower is not clean after one

washing, soak it and let it stand for 30 minutes.
Then repeat the process.

8. Run the mower again for one to three minutes

to remove excess water.

A broken or missing washout ﬁtting
could expose you and others to thrown
objects or blade contact. Contact with
blade or thrown debris can cause injury
or death.

•

Replace broken or missing washout
ﬁtting immediately, before using
mower again.

•

Plug any hole(s) in mower with bolts
and locknuts.

•

Never put your hands or feet under
the mower or through openings in
the mower.

43

«
...
41
42
43
44
45
...
»

Содержание TimeCutter ZD530





















































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZD530

Бренд: Walker Страницы: 100

Бренд: MTD Страницы: 12

Бренд: Grizzly Страницы: 76

Бренд: Mac allister Страницы: 24

Бренд: Simplicity Страницы: 4

Бренд: Gravely Страницы: 36

GLM 40/140 P EASY

Бренд: F.F. Group Страницы: 96

Бренд: Scag Power Equipment Страницы: 38

Бренд: Flymo Страницы: 11

Z Master Professional 7500-D Series

Бренд: Toro Страницы: 80

Бренд: Simplicity Страницы: 16

Бренд: RedMax Страницы: 40

Бренд: Toro Страницы: 60

HR 4600 Turbo 67862

Бренд: Jacobsen Страницы: 224

Бренд: AMBROGIO Страницы: 30

Бренд: Toro Страницы: 24

Бренд: Honda Страницы: 81

Бренд: Yard-Man Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды