Toro TimeCutter ZD530 Скачать руководство пользователя

Страница: 10 / 52

110-6567

1. Warning—read the

Operator’s Manual.

2. Warning—read the instructions before servicing or performing maintenance; move the motion control levers to the brake position,

remove the ignition key and disconnect the spark plug wire.

3. Cutting/dismemberment hazard, mower blade; entanglement hazard, belt—do not open or remove safety shields while engine is

running.

4. Loss of traction/control hazard, slopes—loss of traction/control on a slope, disengage the blade control switch (PTO), proceed

off the slope slowly.

5. Crushing/dismemberment hazard of bystanders, reversing; crushing/dismemberment hazard of bystanders—do not carry

passengers, look behind and down when reversing.

6. Tipping hazard—do not mow up and down slopes, only mow across slopes less than 15 degrees, avoid sudden and sharp

turns while on slopes.

7. Thrown object hazard—keep bystanders a safe distance from the machine, pick up debris before operating, keep deector in place.

Содержание TimeCutter ZD530





















































Результаты поиска

Содержание TimeCutter ZD530

Отзывы:

Похожие инструкции для TimeCutter ZD530

Бренды по названию

Популярные бренды

Toro TimeCutter ZD530, Руководство оператора

Результаты поиска

Содержание TimeCutter ZD530

Отзывы:

Похожие инструкции для TimeCutter ZD530

Бренды по названию

Популярные бренды