Toro TimeCutter ZD530 Скачать руководство пользователя | Manualshive

Страница: 35 / 52

background image

Incorrect battery cable routing could
damage the machine and cables causing
sparks. Sparks can cause the battery
gasses to explode, resulting in personal
injury.

•

Always disconnect the negative
(black) battery cable before
disconnecting the positive (red)
cable.

•

Always connect the positive (red)
battery cable before connecting the
negative (black) cable.

5. Slide the rubber cover up the positive (red)

cable. Disconnect the positive (red) cable from
the battery post (Figure 43).

6. Remove the battery hold-down (Figure 43) and

lift the battery from the battery tray.

Figure 43

1. Battery

4. Negative battery cable

2. Terminal boot

5. Battery hold-down

3. Positive battery cable

6. Bolt, nut, and washer

Checking the Battery Electrolyte Level

Battery electrolyte contains sulfuric acid
which is a deadly poison and causes severe
burns.

•

Do not drink electrolyte and avoid
contact with skin, eyes or clothing. Wear
safety glasses to shield your eyes and
rubber gloves to protect your hands.

•

Fill the battery where clean water is
always available for ﬂushing the skin.

1. Tip the seat forward to see the battery.
2. Look at the side of the battery. The electrolyte

must be up to the Upper line (Figure 44).
Do not allow the electrolyte to fall below the
Lower line (Figure 44).

Figure 44

1. Vent caps

3. Lower line

2. Upper line

3. If the electrolyte is low, add the required amount

of distilled water; refer to Adding Water to
the Battery in Electrical System Maintenance,
page 34.

Adding Water to the Battery

The best time to add distilled water to the battery is
just before you operate the machine. This lets the
water mix thoroughly with the electrolyte solution.
1. Remove the battery from the machine;

refer to Removing the Battery in
Electrical System Maintenance, page 34.

Important:

Never ﬁll the battery with

distilled water while the battery is installed
in the machine. Electrolyte could be
spilled on other parts and cause corrosion.

2. Clean the top of the battery with a paper towel.
3. Remove the vent caps from the battery

(Figure 44).

35

«
...
33
34
35
36
37
...
»

Содержание TimeCutter ZD530





















































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter ZD530

Бренд: Ybravo Страницы: 2

Бренд: Ybravo Страницы: 16

Бренд: MasterCraft Страницы: 24

Бренд: Ryobi Страницы: 16

GLM 40/124 P EASY

Бренд: F.F. Group Страницы: 128

Бренд: MTD Страницы: 16

Бренд: Sabo Страницы: 280

Broardmoor 2600, 1600, LT Series

Бренд: Simplicity Страницы: 2

Бренд: Jacobsen Страницы: 58

Бренд: Nakayama Страницы: 80

Бренд: Oleo-Mac Страницы: 42

Бренд: Cub Cadet Страницы: 1

Бренд: Cub Cadet Страницы: 2

Бренд: Kubota Страницы: 178

Бренд: Snapper Страницы: 68

Бренд: Gardena Страницы: 13

Бренд: Iseki Страницы: 20

Бренд: Iseki Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды