Toro TimeCutter 74750 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

background image

Maintenance

Note:

Determine the left and right sides of the machine from the normal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 5 hours

• Change the engine oil and filter.

Before each use or daily

• Check the safety-interlock system.
• Clean and check the air cleaner foam element.
• Check the engine-oil level.
• Clean the engine air-intake screen.
• Check the cutting blades.
• Inspect the grass deflector for damage

After each use

• Clean the mower-deck housing.

Every 25 hours

• Grease all lubrication points.
• Check tire pressure.
• Check the belts for wear/cracks.

Every 50 hours

• Replace the air cleaner paper element.
• Check the spark plug.

Every 100 hours

• Change the engine oil (change it more often under a heavy load or in high

temperatures).

• Change the engine-oil filter.
• Replace the spark plug.
• Replace the in-line fuel filter.
• Clean the engine-cooling fins and shrouds.

Before storage

• Charge the battery and disconnect battery cables.
• Perform all maintenance procedures listed above before storage.
• Paint any chipped surfaces.

CAUTION

If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure
you or other bystanders.

Remove the key from the ignition and disconnect the wire from the spark plug before you do any
maintenance. Set the wire aside so that it does not accidentally contact the spark plug.

26

«
...
24
25
26
27
28
...
»

Содержание TimeCutter 74750

















































Отзывы:

Нет отзывов

Похожие инструкции для TimeCutter 74750

Бренд: Land Pride Страницы: 60

Бренд: Yard-Man Страницы: 32

Бренд: Yard-Man Страницы: 36

Lawn Queen 21''

Бренд: Jacobsen Страницы: 19

CheckMate 21462

Бренд: Big League Lawns Страницы: 4

Бренд: Yard-Man Страницы: 11

Бренд: Yazoo/Kees Страницы: 24

Бренд: Yardworks Страницы: 35

Бренд: Scag Power Equipment Страницы: 41

Бренд: Snapper Страницы: 44

BOXER AGRI FA Series

Бренд: De Heus Страницы: 14

Shop Series RS8080

Бренд: Rockwell Страницы: 16

Бренд: Cub Cadet Страницы: 72

Бренд: Southland Страницы: 66

Бренд: IronCraft Страницы: 44

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды