manualshive.com logo in svg

Toro TimeCutter 74750, Руководство оператора

Поделиться
Скачать
Toro TimeCutter 74750 Скачать руководство пользователя страница 21

Positioning the Seat

Position the seat where you have the best control of the
machine and are most comfortable (

Figure 19

).

Figure 19

Adjusting the Anti-Scalp
Rollers

Whenever you change the height-of-cut, adjust the height
of the anti-scalp rollers.

Note:

Adjust the anti-scalp rollers so the rollers do not touch

the ground in normal, flat mowing areas.

1.

Disengage the blade control switch (PTO), move the
motion control levers to the neutral lock position and
set the parking brake.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Adjust the anti-scalp rollers as shown in

Figure 20

to

match the closest height-of-cut position.

G010233

1

2

3

4

Figure 20

1.

Anti-scalp roller

3.

Flange nut

2.

Bolt

4.

Hole spacing

Adjusting the Motion-Control
Levers

Adjusting the Height

You can adjust the motion-control levers higher or lower for
maximum comfort (

Figure 21

).

g027252

B

A

Figure 21

Adjusting the Tilt

You can adjust the motion-control levers forward or rearward
for your comfort.

1.

Loosen the upper bolt holding the control lever to the
control-arm shaft.

2.

Loosen the lower bolt just enough to pivot the control
lever forward or rearward (

Figure 21

).

3.

Tighten both bolts to secure the control lever in the
new position.

4.

Repeat the adjustment for the other control lever.

21

 

Содержание TimeCutter 74750

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды