Toro 78490 Скачать руководство пользователя страница 20

20

9. Install the grass deflector. Refer to Installing the Grass

Deflector on page 20.

10. Remove both front weights (Figures 22 and 24).

Installing the Grass Deflector

The grass deflector spring will have either an L end or a
straight end (Fig. 30).

Note: Make sure the grass deflector is installed when the
bagger and tubes are removed.

An uncovered discharge opening could allow the
lawn mower to throw objects in the operator’s or
bystander’s direction and result in serious injury.
Also, contact with the blade could occur.

Never operate the lawn mower unless you install a
cover plate, a mulch plate, grass deflector or a
grass chute and catcher.

Warning

1. Place spacer and spring onto grass deflector. Place the L

or the straight end of spring behind deck edge.

Note: Make sure the L or the straight end of spring is
installed behind deck edge before installing the bolt as
shown in figure 30.

2. Install bolt and nut. Place J hook end of spring around

grass deflector (Fig. 30).

Important

 

The grass deflector must be lowered down

into position. Lift the deflector up to test that it lowers into
the full down position.

6

1

5

4

2

3

7

8

m–6085

10

9

Figure 30

1.

Bolt

2.

Spacer

3.

Locknut

4.

Spring

5.

Spring installed

6.

Grass Deflector

7.

L end of spring, place
behind mounting bracket
before installing bolt

8.

J hook end of spring

9.

Mounting bracket

10. Straight end—possible

style of spring

Operating and Bagging Tips

Machine Size

Remember that the machine is longer and wider with this
attachment installed. By turning too sharply in confined
places you may damage the attachment or other property.

Trimming

Always trim with the left side of the mower. Do not trim
with the right side of the mower because you could damage
the bagging tubes.

Cutting Height

For optimum bagging performance, set the deck
height–of–cut to remove no more that 2 to 3 inches (51 to
76 mm) or 1/3 of the grass height, which ever is less.
Cutting off more than this will reduce the capacity of the
vacuum system.

Содержание 78490

























Отзывы: