Toro 78490 Скачать руководство пользователя страница 19

19

1. Disengage the PTO, set the parking brake, and chock or

block the tires.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Open the bagger; refer to Opening the Bagger, page 18.

4. With the bagger open, pull out the holding pin and

insert into the hole in the hinge (Fig. 29).

2

3

m–5876

1

Figure 29

1.

Holding pin

2.

Hole in hinge

3.

Hinge

Clearing Obstructions From
the Bagger System

1. Empty the bagger.

2. Disengage the PTO, set the parking brake, and chock or

block the drive wheels.

3. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

4. Remove the complete tube assembly from the bagger

and boot.

5. Remove the boot from the mower.

6. Using a stick or similar object, carefully remove and

clear the obstruction from the mower, upper tube,
middle tube, or boot assembly.

7. After you remove the obstruction, install the complete

bagger system and resume operation. Refer to Installing
the Discharge Tubes on page 16.

Removing the Discharge Tubes

Note: Remember to install the grass deflector when in side
discharge mode. Refer to Installing the Grass Deflector on
page 20.

1. Disengage the PTO, set the parking brake, and chock or

block the drive wheels.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Unlatch the middle tube from the boot and slide apart

(Fig. 25).

4. Remove the tube assembly from the bagger (Fig. 25).

5. Remove the boot from the mounting bracket (Fig. 25).

6. If you are changing to side discharge mode, install the

grass deflector. Refer to Installing the Grass Deflector
on page 20.

Removing the Bagger

Danger

If you operate mower without the bagger installed
or with the discharge tubes and boot removed, you
and others may be injured by thrown debris or cut
by the blade.

Always operate the mower with either the
complete bagger mounted in place or use the
mower in side discharge.

1. Disengage the PTO, set the parking brake, and chock or

block the drive wheels.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Remove the discharge tubes. Refer to removing The

Discharge Tubes on page 19.

4. Remove hairpin cotters and clevis pins from the bagger

and bagger bracket (Fig. 17).

5. Remove the skid plate (Fig. 18).

6. Remove the bagger belt and bagger tensioner arm with

the pulley (Fig. 20).

7. Remove the bagger from the bagger mounting bracket

(Fig. 17).

8. Install the bagger tensioner arm with the pulley and the

skid plate (Fig. 18).

Содержание 78490

























Отзывы: