Toro 74959 Скачать руководство пользователя страница 3

Страница: 3 / 64

Figure 2

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

Contents

Introduction .................................................................. 2
Safety ........................................................................... 4

Safe Operating Practices........................................... 4
Slope Indicator ....................................................... 6
Safety and Instructional Decals ................................. 7

Product Overview .........................................................12

Controls ...............................................................12
Specifications ........................................................13

Operation ....................................................................14

Adding Fuel...........................................................14
Checking the Engine Oil Level .................................15
Breaking In a New Machine .....................................15
Using the Rollover Protection System (ROPS) ............15
Think Safety First ...................................................16
Operating the Parking Brake ....................................16
Operating the Mower Blade Control Switch

(PTO) ...............................................................17

Maintenance .................................................................28

Recommended Maintenance Schedule(s) ......................28
Lubrication ...............................................................29

Lubricating the Machine..........................................29
Greasing the Mower ...............................................29
Lubricate the Caster Wheel Hubs..............................30

Engine Maintenance ..................................................31

Servicing the Air Cleaner .........................................31
Servicing the Engine Oil..........................................32

Servicing the Spark Plug ..........................................35
Check the Spark Arrester (if equipped) ......................36

Fuel System Maintenance ...........................................37

Replacing the Fuel Filter ..........................................37
Servicing the Fuel Tank ...........................................37

Electrical System Maintenance ....................................38

Servicing the Battery...............................................38
Servicing the Fuses .................................................39

Drive System Maintenance .........................................40

Checking the Seat Belt.............................................40
Checking the Rollover Protection System (ROPS)

Knobs ...............................................................40

Adjusting the Tracking ............................................40
Checking the Tire Pressure ......................................41
Checking the Wheel Lug Nuts ..................................41
Checking the Wheel Hub Slotted Nut ........................41
Adjusting the Caster Pivot Bearing ............................41
Using the Clutch Shim ............................................42

Cooling System Maintenance ......................................44

Cleaning the Engine Screen and Engine Oil

Cooler ...............................................................44

Cleaning the Engine Cooling Fins and

Shrouds.............................................................44

Check and Clean the Hydraulic Units.........................45

Brake Maintenance ....................................................45

Adjusting the Parking Brake .....................................45

Belt Maintenance ......................................................46

Inspecting the Belts ................................................46
Replacing the Mower Belt ........................................46
Replacing the Hydraulic Pump Drive Belt...................47

Controls System Maintenance .....................................48

Adjusting the Control Handle Position ......................48
Adjusting the Motion Control Linkage ......................49
Adjusting the Motion-control Damper ......................50
Adjusting the Motion Control Neutral Lock

Pivot .................................................................50

Hydraulic System Maintenance ....................................51

Servicing the Hydraulic System.................................51

Mower Deck Maintenance...........................................53

Leveling the Mower Deck ........................................53
Servicing the Cutting Blades.....................................54
Removing the Mower Deck .....................................57
Replacing the Grass Deflector ..................................58

Cleaning ...................................................................58

Cleaning Under the Mower ......................................58
Waste Disposal.......................................................58

Storage ........................................................................59

Cleaning and Storage ..............................................59

Troubleshooting ...........................................................60
Schematics ...................................................................62

Содержание 74959

































































Результаты поиска

Содержание 74959

Отзывы:

Похожие инструкции для 74959

Бренды по названию

Популярные бренды

Toro 74959, Руководство оператора

Результаты поиска

Содержание 74959

Отзывы:

Похожие инструкции для 74959

Бренды по названию

Популярные бренды