Toro 74959 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 64

background image

Adjusting the Motion-control
Damper

The top damper-mounting bolt can be adjusted to obtain a
more desired motion-control lever resistance. See Figure 79
for mounting options.

Figure 79

RH Motion Control Shown

1.

Torque the lock nut to 23 N-m (17 ft-lb). The bolt must
protrude past the end of the locknut after torquing.

2.

Most resistance (firmest feel)

3.

Damper

4.

Medium resistance (medium feel)

5.

Least resistance (softest feel)

Adjusting the Motion Control
Neutral Lock Pivot

The flanged nut can be adjusted to obtain a more desired
motion control lever resistance when moving it to the neutral
lock position. See Figure 80 for adjustment options.

1.

Loosen the jam nut.

2.

Tighten or loosen the flanged nut to the desired feel.

For more resistance, tighten the flanged nut.

For less resistance, loosen the flanged nut

3.

Tighten the jam nut.

Figure 80

1.

Flanged nut

2.

Jam nut

50

«
...
48
49
50
51
52
...
»

Содержание 74959

































































Отзывы:

Нет отзывов

Похожие инструкции для 74959

Бренд: Yard Machines Страницы: 20

Бренд: Texas Страницы: 28

Бренд: Qualcast Страницы: 20

532 42 27-27 Rev. 2

Бренд: McCulloch Страницы: 28

Бренд: Toro Страницы: 2

Бренд: Peco Страницы: 12

Бренд: Poulan Pro Страницы: 48

Z Master 74902TE

Бренд: Toro Страницы: 80

Бренд: Poulan Pro Страницы: 60

Бренд: Snapper Страницы: 28

Бренд: Poulan Pro Страницы: 4

Бренд: Cramer Страницы: 216

Southern States SO15538LT

Бренд: Southern States Страницы: 64

Бренд: Task Force Страницы: 10

Бренд: Southland Страницы: 66

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды