Toro 74959 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 64

background image

Storage

Cleaning and Storage

1.

Disengage the power take off (blade control switch
(PTO), set the parking brake, and turn the ignition key
to the off position. Remove the key.

2.

Remove grass clippings, dirt, and grime from the
external parts of the entire machine, especially the
engine and hydraulic system. Clean dirt and chaff from
the outside of the engine cylinder head fins and blower
housing.

Important:

You can wash the machine with mild

detergent and water. Do not pressure wash the
machine. Avoid excessive use of water, especially
near the control panel, engine, hydraulic pumps,
and motors.

3.

Check the brake; refer to Brake Maintenance (page 45).

4.

Service the air cleaner; refer to Servicing the Air
Cleaner (page 31).

5.

Grease the machine; refer to Lubricating the Machine
(page 29).

6.

Change the crankcase oil; refer to Changing the Engine
Oil (page 34).

7.

Check the tire pressure; refer to Checking the Tire
Pressure (page 41).

8.

Change the hydraulic filters; refer to Servicing the
Hydraulic System (page 51).

9.

Charge the battery; refer to Servicing the Battery (page
38).

10.

Scrape any heavy buildup of grass and dirt from the
underside of the mower, then wash the mower with
a garden hose.

Note:

Run the machine with the blade control switch

(PTO) engaged and the engine at high idle for 2 to
5 minutes after washing.

11.

Check the condition of the blades; refer to Servicing
the Cutting Blades (page 54).

12.

Prepare the machine for storage when non-use occurs
over 30 days. Prepare the machine for storage as
follows:

A.

Add a petroleum based stabilizer/conditioner to
fuel in the tank. Follow mixing instructions from
the stabilizer manufacturer. Do not use an alcohol
based stabilizer (ethanol or methanol).

Note:

A fuel stabilizer/conditioner is most

effective when mixed with fresh fuel and used at
all times.

B.

Run the engine to distribute conditioned fuel
through the fuel system (5 minutes).

C.

Stop the engine, allow it to cool, and drain the
fuel tank; refer to Servicing the Fuel Tank (page
37) in the Maintenance Section.

D.

Restart the engine and run it until it stops.

E.

Dispose of fuel properly. Recycle as per local
codes.

Important:

Do not store

stabilizer/conditioned fuel over 90 days.

13.

Check and tighten all bolts, nuts, and screws. Repair or
replace any part that is damaged.

14.

Paint all scratched or bare metal surfaces. Paint is
available from your Authorized Service Dealer.

15.

Store the machine in a clean, dry garage or storage area.
Remove the key from the ignition switch and keep it
out of reach of children or other unauthorized users.
Cover the machine to protect it and keep it clean.

59

«
...
57
58
59
60
61
...
»

Содержание 74959

































































Отзывы:

Нет отзывов

Похожие инструкции для 74959

Бренд: P1PE Страницы: 28

Бренд: Yard Machines Страницы: 44

Бренд: Yardworks Страницы: 21

Бренд: Yard Machines Страницы: 16

Craftsman EZ3 917.259553

Бренд: Sears Страницы: 56

Бренд: White Outdoor Страницы: 4

Бренд: Spearhead Страницы: 64

Бренд: Gravely Страницы: 52

Бренд: Baroness Страницы: 66

Бренд: Lastec Страницы: 51

Бренд: MTD Страницы: 12

Бренд: Poulan Pro Страницы: 32

Бренд: Yard Machines Страницы: 16

Бренд: Yard-Man Страницы: 12

Бренд: Active Страницы: 40

Бренд: Active Страницы: 44

Бренд: dormak Страницы: 24

Бренд: Black & Decker Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды